TQD100YGE 100 WATT Datasheet

TQD100YGE Datasheet, PDF, Equivalent


Part Number

TQD100YGE

Description

DUAL OUTPUT/ 100 WATT

Manufacture

Power-One

Total Page 3 Pages
Datasheet
Download TQD100YGE Datasheet


TQD100YGE
TQD SERIES - DUAL OUTPUT, 100 WATT
DESCRIPTION
The TQD DC/DC converters are high power, dual output,
fully isolated converters that feature high efficiency, 1500
VDC isolation, and open-frame packaging. The TQD
family allows board designers to deliver any combination
of power from either output, up to each model’s maximum
rating. The TQD series is available in 5V/3.3V or
3.3V/2.5V combinations. The TQD uses planar
magnetics and has an MTBF of over a million hours.
FEATURES
• Independent Dual
Outputs
• Flexible Load Sharing
• High Efficiency
• Open Frame Design
• Planar Magnetics
• Synchronous
Rectification
• Independent Trim For
Each Output
• 1500V Isolation
• 100°C Baseplate
Operation
TECHNICAL SPECIFICATIONS
Input
Voltage range
5 VDC nominal
12 VDC nominal
Reflected ripple
Input Reverse Voltage Protection
18 - 36 VDC
36 - 72 VDC
50 mA
Shunt Diode
Output
Setpoint Accuracy
±1%
Line Regulation Vin Min. - Vin Max., Iout Rated, Output 1
Load Regulation Iout Min. - Iout Max., Vin Nom., Output 1
Minimum Output Current, Each Output
Dynamic Regulation, Loadstep
Pk Deviation
Settling Time
0.2% Vout
0.3% Vout
10 % Iout Rated
25% Iout
4% Vout
500 µs
Voltage Trim Range
±10%
Power Limit Threshold Range, % of Iout Rated
OVP Trip Range
UVP Trip Range
110 - 130%
115 - 140% Vout Nom.
70 - 90%
General
Turn-On Time
Remote Shutdown
Switching Frequency
Isolation
Input - Output
Input - Case
Output - Case
Temperature Coefficient
Case Temperature
Operating Range
Storage Range
Thermal Shutdown Range
Humidity Max., Non-Condensing
Vibration, 3 Axes, 5 Min Each
MTBF† (Bellcore TR-NWT-000332)
Safety
Weight (Approx.)
20 ms
Positive Logic
250 kHz
1500 VDC
1050 VDC
500 VDC
0.03 %/°C
-40 To +100°C
-40 To +125°C
105 To 115°C
95%
5g
1.2 X 106 hrs
UL, cUL, TUV
3.8 oz
Efficiency vs. Load (48V Input)
90
85
80
75
70
TQD085ZED
65 TQD100ZGE
60
55
10 20 30 40 50 60 70 80 90 100
LOAD %
Notes
MTBF predictions may vary slightly from model to model.
Specifications typically at 25°C, normal line, and full load, unless
otherwise stated.
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with
commercial wave-soldering equipment.
Units are water-washable and fully compatible with commercial spray or
immersion post wave-solder washing equipment.
REV. 10/01
1

TQD100YGE
TQD SERIES - DUAL OUTPUT, 100 WATT
MODELS - (See the last page of Section for options.)
MODEL
INPUT VOLTAGE
(VOLTS)
INPUT VOLTAGE
RANGE (VOLTS)
MAXIMUM INPUT
CURRENT (AMPS)*
OUTPUT
VOLTAGE (VOLTS)
TQD100YGE-A
24
18-36
7.4 5.0/3.3
TQD080Z2.0-A
48
36-72
1.9 3.3/2.0
TQD085ZED-A
48
36-72
2.5 3.3/2.5
TQD100ZGE-A
48
36-72
3.7 5.0/3.3
NOTES: Advanced product release - consult factory.
* Maximum input current at minimum input voltage, maximum rated output power.
** At nominal Vin, rated output.
Current can be drawn from either output to its maximum value, or from both outputs.
RATED OUTPUT
CURRENT (AMPS)
20/25
15/15
20/25
20/25
RIPPLE & NOISE
pk-pk (mV)
100/75
100/75
100/75
100/75
TYPICAL
EFFICIENCY**
81%
80%
82%
83%
MECHANICAL DRAWING
-0.160"
(-4.1mm)
0.320"
(8.1mm)
0.800"
(20.3mm)
-0.60"
(-15.2mm)
0.080" 0.560"
(2.0mm) (14.2mm)
1.690" 2.170"
(42.9mm) (55.1mm)
1.450"
(36.8mm)
1.930"
(49.0mm)
2.410"
(61.2mm)
MOUNTING INSERTS
M3X.5 THROUGH 4PL
0.18"
(4.6mm)
2.000"(50.8mm)
56789
10 11 12 13 14
DIA 0.080"
(2.0mm)
4PL
BOTTOM VIEW
2.40"
(61.0mm)
0
-0.20"(-5.1mm)
1
-0.400" 0
(-10.2mm)
234
0.750"
(19.1mm)
1.500" 2.250" 2.650"
(38.1mm) (57.2mm) (67.3mm)
3.45"
(87.6mm)
DI(A1.00.m04m0)" 10PL
0.0(02.56"mRmE)F.
0.50"
(12.7mm)
Thermal Impedance
Natural Convection
100 LFM
200 LFM
300 LFM
400 LFM
5.7 °C/W
3.9 °C/W
2.6 °C/W
1.9 °C/W
1.7 °C/W
Note:
Thermal impedance data is dependent
on many environmental factors. The
exact thermal performance should be
validated for specific application.
Pin Function
1 -Vin
2 Enable
3 Case
4 +Vin
5 +Vout1
6 + Sense 1
7 Trim 1
8 - Sense 1
9 -Vout1
10 -Vout2
11 - Sense 2
12 Trim 2
13 + Sense 2
14 + Vout2
2
Tolerances
Inches:
.XX ± 0.020
.XXX ± 0.010
(Millimeters)
.X ± 0.5
.XX ± 0.25
Pin:
± 0.002
± 0.05
(Dimensions as listed unless
otherwise specified.)


Features TQD SERIES - DUAL OUTPUT, 100 WATT DESCR IPTION The TQD DC/DC converters are hig h power, dual output, fully isolated co nverters that feature high efficiency, 1500 VDC isolation, and open-frame pack aging. The TQD family allows board desi gners to deliver any combination of pow er from either output, up to each model ’s maximum rating. The TQD series is available in 5V/3.3V or 3.3V/2.5V combi nations. The TQD uses planar magnetics and has an MTBF of over a million hours . TECHNICAL SPECIFICATIONS Input Voltag e range 5 VDC nominal 12 VDC nominal Re flected ripple Input Reverse Voltage Pr otection FEATURES • Independent Dual Outputs • Flexible Load Sharing • High Efficiency • Open Frame Design Planar Magnetics • Synchronous Rec tification • Independent Trim For Eac h Output • 1500V Isolation • 100°C Baseplate Operation 18 - 36 VDC 36 - 72 VDC 50 mA Shunt Diode Output Setpoi nt Accuracy ±1% Line Regulation Vin Mi n. - Vin Max., Iout Rated, Output 1 0.2% Vout Load Regulation Iout Min. - Iout Max., .
Keywords TQD100YGE, datasheet, pdf, Power-One, DUAL, OUTPUT/, 100, WATT, QD100YGE, D100YGE, 100YGE, TQD100YG, TQD100Y, TQD100, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)