DatasheetsPDF.com

TP3071 Dataheets PDF



Part Number TP3071
Manufacturers National Semiconductor
Logo National Semiconductor
Description COMBO II Programmable PCM CODEC/Filter
Datasheet TP3071 DatasheetTP3071 Datasheet (PDF)

TP3070, TP3071, TP3070-X COMBO II Programmable PCM CODEC/Filter April 1994 TP3070, TP3071, TP3070-X COMBO ® II Programmable PCM CODEC/Filter General Description The TP3070 and TP3071 are second-generation combined PCM CODEC and Filter devices optimized for digital switching applications on subscriber line and trunk cards. Using advanced switched capacitor techniques, COMBO II combines transmit bandpass and receive lowpass channel filters with a companding PCM encoder and decoder. The devices a.

  TP3071   TP3071



Document
TP3070, TP3071, TP3070-X COMBO II Programmable PCM CODEC/Filter April 1994 TP3070, TP3071, TP3070-X COMBO ® II Programmable PCM CODEC/Filter General Description The TP3070 and TP3071 are second-generation combined PCM CODEC and Filter devices optimized for digital switching applications on subscriber line and trunk cards. Using advanced switched capacitor techniques, COMBO II combines transmit bandpass and receive lowpass channel filters with a companding PCM encoder and decoder. The devices are A-law and µ-law selectable and employ a conventional serial PCM interface capable of being clocked up to 4.096 MHz. A number of programmable functions may be controlled via a serial control port. Channel gains are programmable over a 25.4 dB range in each direction, and a programmable filter is included to enable Hybrid Balancing to be adjusted to suit a wide range of loop impedance conditions. Both transformer and active SLIC interface circuits with real or complex termination impedances can be balanced by this filter, with cancellation in excess of 30 dB being readily achievable when measured across the passband against standard test termination networks. To enable COMBO II to interface to the SLIC control leads, a number of programmable latches are included; each may be configured as either an input or an output. The TP3070 provides 6 latches and the TP3071 5 latches. Features n Complete CODEC and FILTER system including: — Transmit and receive PCM channel filters — µ-law or A-law companding encoder and decoder — Receive power amplifier drives 300Ω — 4.096 MHz serial PCM data (max) n Programmable Functions: — Transmit gain: 25.4 dB range, 0.1 dB steps — Receive gain: 25.4 dB range, 0.1 dB steps — Hybrid balance cancellation filter — Time-slot assignment; up to 64 slots/frame — 2 port assignment (TP3070) — 6 interface latches (TP3070) — A or µ-law — Analog loopback — Digital loopback n Direct interface to solid-state SLICs n Simplifies transformer SLIC; single winding secondary n Standard serial control interface n 80 mW operating power (typ) n 1.5 mW standby power (typ) n Designed for CCITT and LSSGR applications n TTL and CMOS compatible digital interfaces n Extended temperature versions available for −40˚C to +85˚C (TP3070V-X) Note: See also AN-614, COMBO II application guide. COMBO ® and TRI-STATE ® are registered trademarks of National Semiconductor Corporation. © 1999 National Semiconductor Corporation DS008635 www.national.com Block Diagram DS008635-1 FIGURE 1. Connection Diagrams DS008635-2 DS008635-4 Order Number TP3070V (0˚C to +70˚C) Order Number TP3070V-X (−40˚C to +85˚C) See NS Package Number V28A Order Number TP3071J See NS Package Number J20A Order Number TP3071N See NS Package Number N20A Pin Descriptions Pin VCC VBB GND FSX Description +5V ± 5% power supply. −5V ± 5% power supply. Ground. All analog and digital signals are referenced to this pin. Transmit Frame Sync input. Normally a pulse or squarewave with an 8 kHz rep.


TP3070 TP3071 TP3076


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)