Document
PREPARED
By:
DATE:
SPEC.
No.
ED-97136 September 14 Pages DIVISION DEVICES DIV 8, 1997
SHARP
ch-\ ,w APPROVED “: BY: r^ >3p J&&/.-i /ti,,99c DATE: ’ ,‘$‘.. i i. 1 :y ‘3 5 ILMZ~~ ,/ ELECTRONIC COMPONENTS GROUP SHARP CORPORATION
i
ISSUE PAGE REPRESENTATIVE
SPECIFICATION
DEVICE SPECIFICATION FOR Business
OPTO-ELECTRONIC
f
dealing
name
PHOTOCOUPLER
MODEL No.
1. These specification sheets include materials protected Please do not reproduce or cause anyone to reproduce
under copyright of Sharp Corporation them without Sharp’s consent.
(“Sharp”).
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets, and the precautions mentioned below. (Precautions) (1) This product is designed for use in the following application areas ; Audio visual equipment Home appliances OA equipment * Measuring equipment Telecommunication equipment (Terminal) Computers [ Tooling machines If the use of the product in the above application areas is for equipment listed in paragraphs (2) or (31, please be sure to observe the precautions given in those respective paragraphs.
l l l l l l
1
(21 Appropriate measures, such as fail-safe design and redundant design considering the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and safety in function and precision, such as ; * Transportation control and safety equipment (aircraft, train, automobile * Traffic signals - Gas leakage sensor breakers * Rescue and security * Other safety equipment [ etc.) equipment
(3) Please do not use this product for equipment which require extremely high reliability and safety in function and precision, such as ; * Space equipment * Telecommunication equipment (for trunk lines) mMedical equipment [ * Nuclear power control equipment
1
1
(4) Please contact and consult with a Sharp sales representative regarding interpretation of the above three paragraphs _ 3. Please contact and consult with a Sharp sales representative
if there are any questions about this product.
for any questions DATE PRESENTED BY
CUSTOMER’S
APPROVAL
~gj?/
DATE BY
T. Matsumura, Department General Manager Engineering Dept. ,I1 Opto-Electronic Devices Div. ELECOM Group SHARP CORPORATION
of
SHARP CORPORATION
1. Application This specitication applies to the outline Model No. PC357. and characteristics of photocoupler
2. Outline Refer to the attached drawing No. CY9269KO2.
3. Ratings
and characteristics sheet, page 5 to 7.
Refer to the attached
4. Reliability Refer to the attached sheet, page 8.
5. Incoming
inspection sheet, page 9.
Refer to the attached
6. Supplement 6.1 Isolation voltage shall be measured in the following method. side and between
(1) Short between anode and cathode on the primary collector and emitter on the secondary side. (2) The dielectric withstand tester with zero-cross
circuit
shall be used.
(3) The wave form of applied voltage shall be a sine wave. 6.2 Packaging specifications sheet, page 10 to 12.
Refer to the attached
SHARP CORPORATION
ED-97136
MODEL No.
1 September
8, 1997
PAGE
PC357NT
2/ 12
6.3 Business
dealing name (“0” mark
indicates
business
dealing name of ordered
product)
Rank mark
Ic blA) I 4.0 to 8.0 6.5 to 13 10 to20 15to30 4.0 to 13 6.5 to 20 10to30 4.0 to 20 6.5 to 30 4.0 to 30 2.5 to 30
Test conditions
I
I
PC357NIT PC357N2T PC357N3T PC357N4T PC357N5T PC357N6T PC357N7T PC357N8T PC357N9T PC357NOT
1 1 1 1 1
A B C D A or B B or C C or D A, B or C B, CorD A, B, C or D A, B, C, D or no mark
I
I
I 1,=5mA
I
I
I
I
I
I
I
I vc,=5v
I
Ta=25%
0
PC357NT
6.4 The following selection shall be made as to the collector-emitter breakdown voltage (BVceo) in parameter 3.2. (Applied to lot No. “J5” [May 19971 or later] Parameter Collector-emitter breakdown voltage Symbol BVCEO Conditions Ic=O. 1mA Ir=O MIN. 70 TYP. MAX. unit V
6.5 This Model is approved Approved
by UL.
Model No. : PC357
UL iile No. : E64380 6.6 This product This product This product is not designed is assembled incorporates against irradiation. input and output. light emitting diode.
with electrical non-coherent
SHARP CORPORATION
6.7 ODS materials This device. component shall not contain the following materials. Also, the following materials shall not be used in the production process for this device * component. Materials for ODS : CFC!,, Halon, Carbon 1.1.1 -Trichloroethane tetrachloride, (Methylchloroform)
6.8 Brominated
flame retardants such as the PBBO, and PBB, are not used
Specific brominated flame retardants in this device component at all.
7. Notes Refer to the attached sheet- l-l, 2.
.