DatasheetsPDF.com

TB2110FN Dataheets PDF



Part Number TB2110FN
Manufacturers Toshiba
Logo Toshiba
Description PLL
Datasheet TB2110FN DatasheetTB2110FN Datasheet (PDF)

PLL For DTS TOSHIBA Bi−CMOS Integrated Circuit Silicon Monolithic TB2110FN TB2110FN The TB2110FN is a high−speed PLL LSI built in a 2 modulus prescaler that can operate with a 1.5V power supply. Each function is controlled via three serial bus lines, allowing you to configure a high−performance digital tuning system. Features · Due to a Bi−CMOS structure, the 1.5V power supply is stepped up and stabilized by a bipolar circuit to drive the CMOS section. Therefore, this chip is best suited fo.

  TB2110FN   TB2110FN



Document
PLL For DTS TOSHIBA Bi−CMOS Integrated Circuit Silicon Monolithic TB2110FN TB2110FN The TB2110FN is a high−speed PLL LSI built in a 2 modulus prescaler that can operate with a 1.5V power supply. Each function is controlled via three serial bus lines, allowing you to configure a high−performance digital tuning system. Features · Due to a Bi−CMOS structure, the 1.5V power supply is stepped up and stabilized by a bipolar circuit to drive the CMOS section. Therefore, this chip is best suited for digital tuning system in headphone stereos. · Built in a prescaler, this IC can operate with TV: 50~250MHz and FM: 40~150MHz (2 modulus type) for the FMIN input or at 0.5~40MHz for the AMIN input (2 modulus type or directly divided). Weight: 0.31g (typ.) · Comes with a 20 bit programmable counter, two parallel output phase comparators, crystal oscillator, reference counter, and a DC / DC converter control circuit. · The crystal oscillator (X’tal) used in this IC is a 75kHz resonator. · The reference frequency can be selected from seven frequencies available. (ref = 1.0~25kHz) · A 20 bit general−purpose counter is built in that can measure the IF and other frequencies. · All device operations are controlled via three serial bus lines. · Operating voltage range: VCC = 1.0~2.5V (Ta = −20~75°C) · Package is SSOP24pin. 1 2002-10-30 Pin Connection TB2110FN (Note) This device is vulnerable to surge voltages. Take it into account when using this device in your system. 2 2002-10-30 Block Diagram TB2110FN 3 2002-10-30 Pin Function Pin No. Symbol Pin Name Function 1 XI 2 XO Crystal oscillator pins 3 Data 4 Clock 5 Period 6 Out-1 7 Out-2 8 Out-3 9 Out-4 Serial data input / output Clock signal input Period signal input General-purpose output port Connect a 75kHz crystal oscillator for the reference frequency to these pins. Serial I / O port. Use this pin to set the divide ratio and divide method, as well as transfer data to and from the controller to control the general-purpose counter and general-purpose I / O port. This is an open-collector output port. Use this port to output control signals. 10 In port General-purpose input port This port accepts the data to be fed to the output bit (out-5). 11 VCONT 12 VDD DC / DC converter control pin CMOS section power supply 13 Stand-by Standby 14 IF-FM 15 VREF2 16 IF-AM 17 A-GND General-purpose counter input Reference pin General-purpose counter input Bipolar section GND This pin controls the DC / DC converter. The VDD power supply from the DC / DC converter is applied to this pin. The device is placed in standby mode when a “L” is input. The device is in active state when a “H” is input. Use this pin for IF signal input on the FM side. Use this pin as the reference of the IF signal. Use this pin for IF signal input on the AM side. — TB2110FN Remarks — — 4 2002-10-30 Pin No. Symbol 18 AM-in 19 VREF1 20 FM-in 21 VCC Pin Name AM / SW signal input pin Reference pin FM / TV signal in.


TB2104F TB2110FN TB2118F


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)