DatasheetsPDF.com

CL331-0471-0-01 Receptacles. CL331-0471-0-10 Datasheet

DatasheetsPDF.com

CL331-0471-0-01 Receptacles. CL331-0471-0-10 Datasheet






CL331-0471-0-10 Receptacles. Datasheet pdf. Equivalent




CL331-0471-0-10 Receptacles. Datasheet pdf. Equivalent





Part

CL331-0471-0-10

Description

(CL331-0471-0-01) Receptacles



Feature


SMT Ultra-Miniature Coaxial Connectors - Mating Heights Owing to the Lowest Pro file and the Lightest U.FL Series Meet s up to 6 GHz Requirement Figure 1. Mat ing Height Comparison (with Hirose Elec tric Products) 2.4(2.5Max) U.FL E.FL sFeatures 1. Mating Heights Owing to Lowest Profile Height from the printed circuit board when mates a receptacle w ith a (right-angle.
Manufacture

HRS

Datasheet
Download CL331-0471-0-10 Datasheet


HRS CL331-0471-0-10

CL331-0471-0-10; ) plug is 2.5 mm maximum. This low Profi le is at the world’s shortest level. qSpace Factor of Mated Connector Figur e 2. U.FL-LP-040 and U.FL-R-SMT 2. Ext remely Small Board Occupation Area Dia. 0.81 U.FL-R-SMT U.FL-LP-066 Dia.1.13 Di a.1.32 3. World’s Lightest These are the world’s lightest coaxial connect ors. Receptacle: 15.7 mg Right-angle pl ugs For Ø 0.81 mm cable:.


HRS CL331-0471-0-10

53.7 mg For Ø 1.13 & 1.32 mm cable: 59 .1 mg 4. Can Be Used Up to a Frequency of 6 GHz To meet the frequency require ments of a wide variety of miniature eq uipment, these connectors offer high fr equency performance from DC to 6 GHz. F igure 3. U.FL-LP-066and U.FL-R-SMT 5. Can Be Used with Automatic Mounting The embossed tape packaging specification of the receptacles .


HRS CL331-0471-0-10

permits automatic mounting. 6. Use of U ltra-Fine Teflon Cable From among the t ypes of suitable cable, Ø 0.8 mm (sing le shield) outside diameter ultra-fine Teflon coaxial cable has been made a st andard specification in consideration o f improving the construction qualities and construction area. An external diam eter Ø1.32 mm (double shield) & Ø1.13 mm (single shield) ul.

Part

CL331-0471-0-10

Description

(CL331-0471-0-01) Receptacles



Feature


SMT Ultra-Miniature Coaxial Connectors - Mating Heights Owing to the Lowest Pro file and the Lightest U.FL Series Meet s up to 6 GHz Requirement Figure 1. Mat ing Height Comparison (with Hirose Elec tric Products) 2.4(2.5Max) U.FL E.FL sFeatures 1. Mating Heights Owing to Lowest Profile Height from the printed circuit board when mates a receptacle w ith a (right-angle.
Manufacture

HRS

Datasheet
Download CL331-0471-0-10 Datasheet




 CL331-0471-0-10
SMT Ultra-Miniature Coaxial Connectors - Mating Heights Owing to the Lowest Profile and the Lightest
U.FL Series
Meets up to 6 GHz Requirement
Figure 1. Mating Height Comparison
(with Hirose Electric Products)
U.FL
E.FL
sFeatures
1. Mating Heights Owing to Lowest Profile
Height from the printed circuit board when mates a receptacle with
a (right-angle) plug is 2.5 mm maximum. This low Profile is at the
world’s shortest level.
2. Extremely Small Board Occupation Area
In comparison with our E.FL Series of SMT coaxial connectors, the
receptacles offer a reduction of approximately 18% of the board
occupation area resulting in an area of just 7.7 mm2.
3. World’s Lightest
These are the world’s lightest coaxial connectors.
Receptacle: 15.7 mg
Right-angle plugs
For Ø 0.81 mm cable: 53.7 mg
For Ø 1.13 & 1.32 mm cable: 59.1 mg
4. Can Be Used Up to a Frequency of 6 GHz
To meet the frequency requirements of a wide variety of miniature
equipment, these connectors offer high frequency performance
from DC to 6 GHz.
5. Can Be Used with Automatic Mounting
The embossed tape packaging specification of the receptacles
permits automatic mounting.
6. Use of Ultra-Fine Teflon Cable
From among the types of suitable cable, Ø 0.8 mm (single shield)
outside diameter ultra-fine Teflon coaxial cable has been made a
standard specification in consideration of improving the
construction qualities and construction area.
An external diameter Ø1.32 mm (double shield) & Ø1.13mm (single
shield) ultra-fine Teflon coaxial cable specification is also available.
7. Simple Removal of Connectors
The extraction jig permits simple removal of connectors.
8. Mating Checks Are Easy
Subminiature size notwithstanding, the lock sensation permits a
check of sure mating.
qSpace Factor of Mated Connector
Figure 2. U.FL-LP-040 and U.FL-R-SMT
U.FL-R-SMT
U.FL-LP-040
Figure 3. U.FL-LP-066and U.FL-R-SMT
U.FL-R-SMT
U.FL-LP-066
sApplications
Mobile phones, wireless communications
equipment, electronic measuring instruments,
GPS, wireless LAN, Bluetooth etc.
2002.3
1




 CL331-0471-0-10
s Product Specifications
Ratings
Nominal characteristic impedance
Rated voltage
Rated frequency
50ø
60 V AC (rms)
DC to 6 GHz
Operating temperature range
Operating humidity
-40˚C to +90˚C
90% max.
Item Specification
1. Contact resistance
Center: 20 mø max.
Outside: 10 mø max.
2. Insulation resistance
3. Withstand voltage
4. V.S.W.R.*
500 Mø min.
No line or insulation breakdown
1.3 max.
Dia.0.81Cable
Dia.1.13Cable
Dia.1.32Cable
5. Female contact holding force 0.15 N min.
1.35
1.4
1.5
6. Repetitive operation
Contact
resistance
25
15
mø
mø
max.
max.
(Center)
(Outside)
7. Vibration
No momentary disconnections of 1 µs min.
No damage, cracks, or parts looseness min.
Conditions
Measured at 10 mA max.
Measured at 100 V DC
200 V AC for 1 minute
DC to 3 GHz
3 to 6 GHz
Measured with a Ø 0.475 pin gauge
30 cycles of insertion and disengagement
Frequency of 10 to 100 Hz, single amplitude of 1.5 mm,
acceleration of 59 m/s2, for 5 cyles in the direction of each of the 3 axes
8. Shock
No momentary disconnections of 1 µs min.
No damage, cracks, or parts looseness
Acceleration of 735 m/s2, 11 ms duration, sine half-wave
waveform, for 6 cycles in the direction of each of the 3 axes
9. Humidity resistance
9. (Steady state)
No damage, cracks, or parts looseness
Insulation resistance 100 Mø min.(High temperature)
Insulation resistance 500 Mø min.(Pry)
Temperature of 40˚C, humidity of 95%,
let stand for 96 hours
10. Temperature cycle
No damage, cracks, or parts looseness
Contact resistance 25 mø max. (Center)
15 mø max. (Outside)
Temperature: +40˚C / 5 to 35˚C / +90˚C / 5 to 35˚C
Time:
30 min. / Within 5 min. / 30 min. / Within 5 min.
Cycles: 5
11. Salt spray test
No excessive corrosion
48 hours continuous exposure to 5% salt water
*V.S.W.R. Measurement System
The above V.S.W.R. standard values were measured using the measurement system of the diagram below.
NOTE 1: Cable type connectors were measured with SMA conversion adapters
attached to both ends of the harness product of a suitable 100cm cable.
NOTE 2: Board type connectors were mounted to a 50glass epoxy board and
measurements were conducted with SMA conversion adapters attached.
sMaterials
Part
Shell
Male center contact
Female center contact
Insulator
Material
Phosphor bronze
Brass
Phosphor bronze
Plug
PBT
Receptacle
LCP
Finish
Silver plating
Gold plating
Gold plating
Black
Beige
Remarks
—————
—————
—————
UL94V-0
UL94V-0
2




 CL331-0471-0-10
sPlugs
U.FL-LP-040
Form of Plug After Cable Wiring
U.FL-LP-066
Item
HRS No.
Right-angle plug shell
(for Ø 0.81 cable)
CL331-0451-2
Part No.
U.FL-LP-040
Form of Plug After Cable Wiring
Applicable Cable
RF-MF5010 Manufactured by Nissei Electric Co., Ltd.
J12B0964 Manufactured by Junkosha Co., Ltd.
CO-6F-SB-CX50 Manufactured by Hitachi Cable, Ltd.
Right-angle plug shell
(for Ø 1.13 cable)
Right-angle plug shell
(for Ø 1.32 cable)
CL331-0452-5
U.FL-LP-066
RF-MF5016 Manufactured by Nissei Electric Co., Ltd.
J12B1054 Manufactured by Junkosha Co., Ltd.
A12B0733 Manufactured by Junkosha Co., Ltd.
CO-6F-DSB-CX-50 Manufactured by Hitachi Cable, Ltd.
Please order plugs with the cable assembly specifications.
sCable Assembly
Dimension of U.FL Series assembly products should be made as indicated below.
Single-Ended Cable Assembly
Double-Ended Cable Assembly
Weight (mg)
53.7/unit
59.1/unit
qOrdering Information
U.FL - [] LP - [] - A - (L)
12
3
4
1 Series name
2 Assembly type
3 Cable type
4 Overall length (mm)
U.FL
Blank: Single ended
2: Double ended
04 : For use with Ø 0.81 cable
5016 : For use with Ø 1.13 cable
066 : For use with Ø 1.32 cable
Length L is expressed in mm units.
qCable Assembly Overall Length Standard Tolerance
Overall Length L (mm)
0035<=L<=0200
0200<L<=0500
0500<L<=1000
1000<L<=1000
Standard Tolerance (mm)
±04
±08
±12
±1.5%
Note: Shortest length L is 35 mm.
Part No. of Cable Assembly
CL No.
Description
U.FL-2LP-04-A-(L)
U.FL-LP-04-A-(L)
321-1937-2-**
321-1998-7-**
Dia. 0.81mm Double Ended Cable Assembly
Dia. 0.81mm Single Ended Cable Assembly
U.FL-2LP-5016-A-(L)
U.FL-LP-5016-A-(L)
U.FL-2LP-066-A-(L)
321-2493-6-**
321-2492-3-**
321-2170-7-**
Dia. 1.13mm Double Ended Cable Assembly
Dia. 1.13mm Single Ended Cable Assembly
Dia. 1.32mm Double Ended Cable Assembly
U.FL-LP-066-A-(L)
321-2573-3-**
Dia. 1.32mm Single Ended Cable Assembly
Please contact Hirose Sales Representative about cable length and cable end treatment.
3



Recommended third-party CL331-0471-0-10 Datasheet






@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)