DatasheetsPDF.com

HI-M602V0 Dataheets PDF



Part Number HI-M602V0
Manufacturers Hunin Electronics
Logo Hunin Electronics
Description (HI-M600V0 Series) Photo IC
Datasheet HI-M602V0 DatasheetHI-M602V0 Datasheet (PDF)

t PRODUCTION SPECIFICATION e e : REMOTE CONTROL RECEIVER MODULE PRODUCT LINE h TITLE : S HI-M600V0 series a t a 1. Description D The.HI-M600V0 series are receiver units for infrared remote control system. w Assembled high performance PIN photodiode and preamplifier on lead frame is w w molded in uniquely disigned epoxy package with daylight cut filter & metal shield case. 4U . m o c 2. Features ◇ Low power consumption ◇ Possible to direct connection to TTL & CMOS ◇ Low sensitivity against fl.

  HI-M602V0   HI-M602V0



Document
t PRODUCTION SPECIFICATION e e : REMOTE CONTROL RECEIVER MODULE PRODUCT LINE h TITLE : S HI-M600V0 series a t a 1. Description D The.HI-M600V0 series are receiver units for infrared remote control system. w Assembled high performance PIN photodiode and preamplifier on lead frame is w w molded in uniquely disigned epoxy package with daylight cut filter & metal shield case. 4U . m o c 2. Features ◇ Low power consumption ◇ Possible to direct connection to TTL & CMOS ◇ Low sensitivity against fluorescent lamp driven by inverter ◇ Open collector output with a pull-up resistance ◇ Various Band Pass Filter frequency 3. HI-M600V0 Series Models ◇ HI-M601V0 ◇ HI-M602V0 ◇ HI-M603V0 ◇ HI-M604V0 ◇ HI-M605V0 40.0KHz 38.0KHz 56.7KHz 32.7KHz 36.7KHz 4. Block Diagram w PD Amplifier w w .D t a S a e h t e U 4 .c m o Vcc RL Auto Gain Controler Band Pass Filter Vout Demodulator Comparator Constant Voltage Integrator Peak Hold GND w w w .D at h S a t e e 4U . m o c PRODUCTION SPECIFICATION PRODUCT LINE : REMOTE CONTROL RECEIVER MODULE TITLE : HI-M600V0 series 5. Absolute Maximum Ratings Parameter Supply voltage Operating temperature Storge temperature Soldering temperature *1 *1. Within 5 seconds Symbol Vcc Topr Tstg Tsol Rating 6.0 -10 ~ +60 -20 ~ +75 260 Unit V ℃ ℃ ℃ 6. Recommended Operating Conditions Parameter Supply voltage * In case of Vcc include noise factor please add the R-C line filter as shown 47㎌~100㎌ Symbol Vcc VCC Operating condition 4.7 ~ 5.3 33Ω~100Ω Unit V + _ IR Receiver Unit VOUT GND 7. Electro-optical Characteristics Parameter Current consumption High level output voltage Low level output voltage High level pulse width Low level pulse width B.P.F. center frequency Peak sensitive wavelength Detecting distance Detecting half angle Symbol Min. Typ. Max. Icc 1.8 2.3 3.0 VOH 4.0 5.0 Vcc VOL 0.35 0.5 TWH 200 400 600 TWL 200 400 600 fo 40.0,38.0,56.7,32.7,36.7 λP 940 L 8.0 Δθ ±45 Unit mA V V ㎲ ㎲ KHz nm m deg Ta=25℃,Vcc=5V Remark No input signal *2. *2. *2. *2. *2. *2. Ee=200LUX Horizontal direction *2 The output signal and detecting distance of this receiver unit shall satisfy the following requirements with the transmitter specified as below (Fig.1) in the optical standard system (Fig.2). (1) Standard transmitter A transmitter output shall be set as Vout=40mVpp, and the burst wave as shown in the figure shall be transmitted by the transmitter. however the HI-D470R in this application is Pin Photodiode which has a characteristics as short-circuit current Isc=25mA at Ev=1000LUX(2856。K standard light source), spectral sensitivity l=880~1050nm. PRODUCTION SPECIFICATION PRODUCT LINE : REMOTE CONTROL RECEIVER MODULE TITLE : HI-M600V0 series 20 ㎝ 10 ㏀ +5V fo VO 400㎲ ㎲ 600 400㎲ 600 10 ㎌ Outpu t waveform Standard transmitter HI-D470R 10 ㏀ Vout Oscilloscope Fig.1 Standard transmitter (2) Standard optical system Using a standard transmitter (Fig.1) output pulse width TWL and TWH is tested at the detector f.


PVM2037 HI-M602V0 HI-M601V0


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)