Document
w
w
w
.D
at
h S a
t e e
4U
.
m o c
MICROCOMPUTER MN102L00
MN102L2503/25A/25D/ 25Z/25G/F25Z/490A/62D/ 62F/62G LSI User's Manual
w
w
w
.D
t a
S a
e h
t e
Pub.No.22262-010E
U 4
.c
m o
w
w
w
.D
at
h S a
t e e
4U
.
m o c
PanaXSeries is a trademark of Matsushita Electric Industrial Co., Ltd. The other corporation names, logotypes and product names written in this manual are trademarks or registered trademarks of their corresponding corporations. The MN102LF25Z is manufactured and sold under the License Agreement with BULL CP8 Inc., and the use of the MN102LF25Z into the IC card is not allowed.
Request for your special attention and precautions in using the technical information and semiconductors described in this manual. (1) The approval of the Japanese Government is required for the export of any products and technologies listed in this manual which are subjected to the provisions of the Foreign Exchange and Foreign Trade Law. The contents of this manual are subject to change without notice to improve design, function, or performance. Matsushita Electronics assumes no responsibility or liability for damages or for infringements of patents or other rights arising from use of the information in this manual. The contents of this manual may not be copied or reproduced without permission in writing from Matsushita Electronics. This manual describes standard specifications. Obtain the latest product standard specifications before you design, purchase, or use.
(2)
(3)
(4)
(5)
For inquiries regarding this manual or any Matsushita semiconductor, please contact one of the sales offices listed at the end of this manual or the sales department of Matsushita Electronics Corporation.
About This Manual
This manual is intended for assembly-language programming engineers. It describes the internal configuration and hardware functions of the MN102L25x series microcontrollers.
Text Conventions
This manual contains titles, sub-titles, special notes and warnings. Supplementary comments appear in the sidebar.
Key Information This note describes key points of an operation. Warning Please read and follow these instructions to prevent damage or reduced performance.
Finding Desired Information
This manual provides four methods for finding desired information quickly and easily. (1) An index for the front of the manual for finding each section. (2) A table of contents at the front of the manual for finding desired titles. (3) A list of figures at the front of the manual for finding illustrations and charts by names. (4) A chapter name is located at the upper corner of each page.
Related Manuals
s MN10200 Series Linear Addressing Version LSI User Manual (Describes the MN10200 series specifications) s MN10200 Series Linear Addressing Version Instruction Manual (Describes the instruction set) s MN10200 Series Linear Addressing Version C Compiler User Manual Usage Guide (Describes the installation, commands, and options for the C complier) s MN10200 Series Linear Addressing Version C Compiler User Manual Language Description (Describes the syntax for the C complier) s MN10200 Series Linear Addressing Version C Compiler User Manual Library Reference (Describes the standard libraries for the C complier) s MN10200 Series Linear Addressing Version Cross Assembler User Manual Language Description (Describes the assembler syntax and notation) s MN10200 Series Linear Addressing Version C Source Code Debugger User Manual (Describes the use of the C source code debugger) s MN10200 Series Linear Addressing Version PanaXSeries Installation Manual (Describes the installation of the C complier, cross-assembler, and C source code debugger and the procedures for using the in-circuit emulator)
Questions and Comments
Please send your questions, comments and suggestions to the semiconductor design center closest to you. See the last page of this manual for a list of addresses and telephone numbers.
Contents
0 1 2 3 4 5 6 7 8 9
Chapter 1 General Description
Chapter 2 Bus Interface
Chapter 3 Interrupts
Chapter 4 Timers
Chapter 5 Serial Interface
Chapter 6 Analog Interface
Chapter 7 ATC
Chapter 8 Ports
Chapter 9 Appendix
Contents
0 1 2 3 4 5 6 7 8 9 10 11
Contents
Chapter 1
1-1 1-1-1 1-1-2 1-1-3 1-2 1-3 1-4 1-5
General Description
2 2 2 5 8 10 12 13 23 Introduction ............................................................................. Features ................................................................................. Overview ................................................................................
General Description ....................................................................................
Basic Specifications ................................................................................... Block Diagram ............................................................................................ Pin Description .......................................................