Document
14 Pin DIP and SMD 5 Tap Low-Profile TTL Compatible Active Delay Lines
Compatible with standard auto-insertable equipment and can be used in either infrared or vapor phase process.
Delays are ±5% or ±2 nS† Total Tap
5, 10, 15, 20 6, 12, 18, 24 7, 14, 21, 28 8, 16, 24, 32 9, 18, 27, 36 10, 20, 30, 40 12, 24, 36, 48 15, 30, 45, 60 20, 40, 60, 80 25, 50, 75, 100 30, 60, 90, 120 35, 70, 105, 140 †Whichever is greater. 25 30 35 40 45 50 60 75 100 125 150 175
DIP Part Number
EP8200-HL EP8213-HL EP8214-HL EP8215-HL EP8216-HL EP8201-HL EP8211-HL EP8217-HL EP8202-HL EP8219-HL EP8203-HL EP8220-HL
SMD Part Number
EPA073HL-25 EPA073HL-30 EPA073HL-35 EPA073HL-40 EPA073HL-45 EPA073HL-50 EPA073HL-60 EPA073HL-75 EPA073HL-100 EPA073HL-125 EPA073HL-150 EPA073HL-175
Delays are ±5% or ±2 nS† Total Tap
40, 80, 120, 160 45, 90, 135, 180 50, 100, 150, 200 60, 120, 180, 240 70, 140, 210, 280 80, 160, 240, 320 84, 168, 252, 336 88, 176, 264, 352 90, 180, 270, 360 84, 188, 282, 376 100, 200, 300, 400 200 225 250 300 350 400 420 440 450 470 500
DIP Part Number
EP8204-HL EP8221-HL EP8205-HL EP8206-HL EP8207-HL EP8208-HL EP8218-HL EP8222-HL EP8209-HL EP8223-HL EP8210-HL
SMD Part Number
EPA073HL-200 EPA073HL-225 EPA073HL-250 EPA073HL-300 EPA073HL-350 EPA073HL-400 EPA073HL-420 EPA073HL-440 EPA073HL-450 EPA073HL-470 EPA073HL-500
Delay times referenced from input to leading edges at 25°C, 5.0V, with no load.
DC Electrical Characteristics Parameter Test Conditions
VOH VOL VIK IIH IIL IOS High-Level Output Voltage Low-Level Output Voltage Input Clamp Voltage High-Level Input Current Low-Level Input Current Short Circuit Output Current VCC = min. V IL = max. I OH = max VCC = min. VIH = min. I OL= max VCC = min. II = IIK VCC = max. V IN = 2.7V VCC = max. V IN = 5.25V VCC = max. V IN = 0.5V VCC = max. V OUT = 0. (One output at a time) VCC = max. V IN = OPEN VCC = max. V IN = 0 Td ≤ 500 nS (0.75 to 2.4 Volts) Td > 500 nS VCC = max. V OH = 2.7V VCC = max. V OL = 0.5V
Min Max Unit
2.7 0.5 -1.2 50 1.0 -2 -100 V V V µA mA mA mA
-40
ICCH High-Level Supply Current ICCL Low-Level Supply Current TRO Output Rise Time NH NL Fanout High-Level Output Fanout Low-Level Output
Recommended Operating Conditions
VCC VIH VIL IIK IOH IOL PW* d* TA Supply Voltage High-Level Input Voltage Low-Level Input Voltage Input Clamp Current High-Level Output Current Low-Level Output Current Pulse Width of Total Delay Duty Cycle Operating Free-Air Temperature
Min
*These two values are inter-dependent.
SMD Package
w
w
.280 Max. .01 Typ.
.D w
40 0
.200 .300
4.75 2.0
t a
Max
5.25 0.8 -18 -1.0 20 40 +70
S a
Unit
V V V mA mA mA % % °C
e h
EIN PW TRI PRR VCC
75 mA 75 mA 4 nS 5 nS 20 TTL LOAD 10 TTL LOAD
t e
U 4
14
.c
VCC
Schematic
m o
12 4 10 6
8
OUTPUT
INPUT 1
7 GROUND
Input Pulse Test Conditions @ 25° C
Pulse Input Voltage Pulse Width % of Total Delay Pulse Rise Time (0.75 - 2.4 Volts) Pulse Repetition Rate @ Td ≤ 200 nS Pulse Repetition Rate @ Td > 200 nS Supply Voltage 3.2 110 2.0 1.0 100 5.0
Unit
Volts % nS MHz KHz Volts
DIP Package
White Dot Pin#1
.200 PCA EP8201-HL Date Code .300 .280 Max.
.400 Max.
PCA EPA073HL-25 Date Code .300 .200
Suggested Solder Pad Layout
.055 .410
.100
.03
.780 Max. .200 Max. .020 Typ.
.780 Max. .165 Max. .02
DSD82XXHL & DSA073HL
.100
Rev. A 2/5/96
.050
.300
Unless Otherwise Noted Dimensions in Inches Tolerances: Fractional = ± 1/32 .XX = ± .030 .XXX = ± .010
w
ELECTRONICS
w
w
.125 ± .01
.D
a
S a t
.020 Min.
e e h
U 4 t
m o .c
.365 Max.
.010 Typ.
QAF-CSO1 Rev. B 8/25/94
INC.
16799 SCHOENBORN ST. NORTH HILLS, CA 91343 TEL: (818) 892-0761 FAX: (818) 894-5791 21
.