DatasheetsPDF.com

EPT7045GM Dataheets PDF



Part Number EPT7045GM
Manufacturers PCA Electronics
Logo PCA Electronics
Description Token Ring Transceiver Module
Datasheet EPT7045GM DatasheetEPT7045GM Datasheet (PDF)

www.DataSheet4U.com Token Ring Transceiver Module ELECTRONICS INC. EPT7045GM • Optimized for Texas Instrument’s TMS38054 • • Supports both UTP and STP Transmission • • Overvoltage Protection Circuit • • Complies with or exceeds IEEE 802.5 Requirements • Electrical Parameters @ 25° C Impedance [Xmit/Rcv] Chip Side 600/150 1-16 MHz Insertion Loss (dB Max.) 32 MHz 36 MHz 44 MHz 1-6 MHz Return Loss (dB Min.) 6-17 MHz 17-25 MHz 1-30 MHz Common Mode Rejection (dB Min.) 30-100 MHz 100 MHz 200-300 MH.

  EPT7045GM   EPT7045GM


Document
www.DataSheet4U.com Token Ring Transceiver Module ELECTRONICS INC. EPT7045GM • Optimized for Texas Instrument’s TMS38054 • • Supports both UTP and STP Transmission • • Overvoltage Protection Circuit • • Complies with or exceeds IEEE 802.5 Requirements • Electrical Parameters @ 25° C Impedance [Xmit/Rcv] Chip Side 600/150 1-16 MHz Insertion Loss (dB Max.) 32 MHz 36 MHz 44 MHz 1-6 MHz Return Loss (dB Min.) 6-17 MHz 17-25 MHz 1-30 MHz Common Mode Rejection (dB Min.) 30-100 MHz 100 MHz 200-300 MHz Rcv -20 -35 Crosstalk (dB Min.) 1-30 MHz Cable Side Xmit Rcv Xmit Rcv Xmit Rcv Xmit Rcv Xmit Rcv Xmit 150/100 -.8 -.8 -7 -1 -25 -1 -35 -1 -15 -20 -15 Rcv Xmit -20 -10 Rcv Xmit Rcv Xmit Rcv Xmit Rcv Xmit -15 -70 -70 -35 -30 -45 -45 -20 Schematic PhPh+ Tx+ Vcc 2 13 14 12 11 .1µF 15 Ts+ Impedance Xmit Matching Filter DataSheet4U.com Network Tx- 10 Gnd 2 9 Gnd 1 3 Rx+ 2 16 Ts- DataShee CMF 17 Tu18 Tu+ 19 Ch Gnd 23 Rs22 Rs+ .1µF Vcc 1 1 CMF 21 Ru+ 20 Ru- Rx- 4 PhRet B 5 PhRet A 6 Package A N Dim. Pin 1 I.D. PCA EPT7045GM Date Code B Q Pad Layout P A B C D E F G H I J K L M N P Q Min. 1.290 .575 .300 1.110 .003 .100 .780 .015 .008 .090 0° .025 Dimensions (Inches) Max. Nom. 1.310 .585 .320 Typ. .020 Typ. .800 .021 .012 Typ. 8° .045 .030 .100 .092 .800 (Millimeters) Min. Max. Nom. 32.77 14.60 7.62 28.19 0.076 2.54 19.81 .381 .203 2.28 0° .635 33.27 14.86 8.13 Typ. .508 Typ. 20.32 .533 .305 Typ. 8° 1.14 .762 2.54 2.34 20.32 D E M C J H F K L G I DataSheet4U.com PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 CST7045GMa Rev. 10/5/96 Product performance is limited to specified parameters. Data is subject to change without prior notice. TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com DataSheet 4 U .com www.DataSheet4U.com Token Ring Transceiver Module ELECTRONICS INC. EPT7045GM The circuit below is a guideline for interconnecting PCA’s EPT7045GM with a typical Token Ring PHY chip for 4 Mb/16Mb applications over STP or UTP cable. Further details of system design should be obtained from the specific chip manufacturer. Note that this module is optimized for a “current source” driver such as TMS38054. Only one type of cable should be driven by the module: either UTP or STP. If you are using 120Ω cable or desire to install only one RJ45 connector thus leaving the STP use with a dongle when needed, please refer to PCA part number EPT7066 or similar parts optimized for 120Ω cable. Note that there is no need for the receiver side filtering. So consider this a cost effective solution for almost all Token Ring applications using this chip or similar chips. The pull down resistors to chassis via a cap shown around the RJ45 connector have been known to suppress unwanted radiation that unused wires pick up from the immediate environment. This is specially true if driving UTP cable. Their placement and use are to be considered carefully before a design is finalized. No specific recommendation is made here for phantom return circuitry: implementation varies. Please note that additional emission control has been observed if both nodes of the phantom bypass capacitor on the transmit channel are pulled to the chassis ground via suitable capacitors. It is recommended that there be a neat separation of ground planes in the layout. It is generally accepted practice to limit the plane off at least 0.05 inches away from the chip side pins of EPT7045GM. There need not be any ground plane beyond this point. For best results, PCB designer should design the outgoing traces preferably to be 75Ω/50Ω (STP/UTP), balanced and well coupled to achieve minimum radiation from these traces. et4U.com DataSheet4U.com Typical Application Circuit Connection to TMS38054 (or Equivalent). Only NIC side shown. RCVINA 100Ω 2 4 PHA +5V 23 22 19 Chassis Ground RCVINB +5V 1(R) 6(G) DB-9 Connector 5(B) 9(O) Use only one connector 4 5 Rcv± 6 5 PHB 50Ω/2W PHOUTA PHOUTB 13 50Ω/2W 10µF 10µF 16 15 21 14 3 +5V TMS38054 11 20 18 RJ45 3 Xmit± 6 1 2 7 8 DROUTB DROUTA 300Ω 300Ω 12 10 EPT7045GM 17 +5V Notes : 1. Pins 5 & 6 are left unconnected. Applications vary. Your system may have a phantom drive return detection circuit needing pins 5 & 6 to be connected separately. 2. Red line connections to DB-9 Connector are 75Ω impedance traces. DataSheet4U.com PCA ELECTRONICS, INC. 16799 SCHOENBORN ST. NORTH HILLS, CA 91343 CST7045GMb Rev. 10/5/96 TEL: (818) 892-0761 FAX: (818) 894-5791 http://www.pca.com DataSheet 4 U .com .


EPT7040 EPT7045GM EPT7055A


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)