10H350P Datasheet | MC10H350P





10H350P PDF File (Datasheet) Download

Part Number 10H350P
Description MC10H350P
Manufacture Motorola
Total Page 4 Pages
PDF Download Download 10H350P PDF File

Features: MOTOROLA SEMICONDUCTOR TECHNICAL DATA P ECL* to TTL Translator (+5 Vdc Power Su pply Only) The MC10H350 is a member of Motorola’s 10H family of high perfor mance ECL logic. It consists of 4 tran slators with differential inputs and TT L outputs. The 3–state outputs can b e disabled by applying a HIGH TTL logic level on the common OE input. The MC 10H350 is designed to be used primarily in systems incorporating both ECL and TTL logic operating off a common power supply. The separate VCC power pins a re not connected internally and thus is olate the noisy TTL VCC runs from the r elatively quiet ECL VCC runs on the pri nted circuit board. The differential in puts allow the H350 to be used as an in verting or noninverting translator, or a differential line receiver. The H350 can also drive CMOS with the addition of a pullup resistor. • Propagation Delay, 3.5 ns Typical • MECL 10K– Compatible MAXIMUM RATINGS Characteri stic Symbol Rating Unit Power Supply (VEE = Gnd) Operating Temperatur.

Keywords: 10H350P, datasheet, pdf, Motorola, MC10H350P, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute, Equivalent

MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
PECL* to TTL Translator
(+5 Vdc Power Supply Only)
The MC10H350 is a member of Motorola’s 10H family of high performance
ECL logic. It consists of 4 translators with differential inputs and TTL outputs.
The 3–state outputs can be disabled by applying a HIGH TTL logic level on the
common OE input.
The MC10H350 is designed to be used primarily in systems incorporating
both ECL and TTL logic operating off a common power supply. The separate
VCC power pins are not connected internally and thus isolate the noisy TTL VCC
runs from the relatively quiet ECL VCC runs on the printed circuit board. The
differential inputs allow the H350 to be used as an inverting or noninverting
translator, or a differential line receiver. The H350 can also drive CMOS with the
addition of a pullup resistor.
Propagation Delay, 3.5 ns Typical
MECL 10K–Compatible
MAXIMUM RATINGS
Characteristic
Symbol
Rating
Unit
Power Supply (VEE = Gnd)
Operating Temperature Range
Storage Temperature Range — Plastic
— Ceramic
VCC
TA
Tstg
7.0
0 to +75
–55 to +150
–55 to +165
Vdc
°C
°C
°C
ELECTRICAL CHARACTERISTICS (VCC = 5.0 V ±5%) (See Note 1)
TA = 0°C to 75°C
Characteristic
Symbol
Min
Max
Unit
Power Supply Current
TTL
ECL
ICC
20 mA
12
Input Current High
Pin 9
Others
Input Current Low
Pin 9
Others
Input Voltage High
Pin 9
Input Voltage Low
Pin 9
Differential Input Voltage (1)
Pins 3–6, 11–14 (1)
IIH
IINH
IIL
IINL
VIH
VIL
VDIFF
2.0
350
20
50
–0.6
50
0.8
µA
mA
µA
Vdc
Vdc
mV
Voltage Common Mode
VCM
2.8
VCC
Vdc
Pins 3–6, 11–14
Output Voltage High
IOH = 3.0 mA
VOH
2.7
— Vdc
Output Voltage Low
IOL = 20 mA
VOL
0.5 Vdc
Short Circuit Current
VOUT = 0 V
IOS
–60
–150
mA
Output Disable Current High
VOUT = 2.7 V
IOZH
50 µA
Output Disable Current Low
VOUT = 0.5 V
IOZL
–50 µA
(1) Common mode input voltage to pins 3–4, 5–6, 11–12, 13–14 must be between the values of 2.8
V and 5.0 V. This common mode input voltage range includes the differential input swing.
(2) For single ended use, apply 3.75 V (VBB) to either input depending on output polarity required.
Signal level range to other input is 3.3 V to 4.2 V.
(3) Any unused gates should have the inverting inputs tied to VCC and the non–inverting inputs tied
to ground to prevent output glitching.
(4) 1.0 V to 2.0 V w/50 pF into 500 ohms.
*Positive Emitter Coupled Logic
MC10H350
L SUFFIX
CERAMIC PACKAGE
CASE 620–10
P SUFFIX
PLASTIC PACKAGE
CASE 648–08
FN SUFFIX
PLCC
CASE 775–02
LOGIC DIAGRAM
9
3
4
2
5
6
7
11
12
10
13
14
15
VCC (+5.0 VDC) = PINS 1 AND 16
GND = PIN 8
DIP
PIN ASSIGNMENT
ECL VCC
AOUT
AIN
AIN
BIN
BIN
BOUT
GND
1
2
3
4
5
6
7
8
16 TTL VCC
15 COUT
14 CIN
13 CIN
12 DIN
11 DIN
10 DOUT
9 OE
Pin assignment is for Dual–in–Line Package.
For PLCC pin assignment, see the Pin Conversion
Tables on page 6–11 of the Motorola MECL Data
Book (DL122/D).
9/96
© Motorola, Inc. 1996
2–57
REV 6

           






Index : 0  1  2  3   4  5  6  7   8  9  A  B   C  D  E  F   G  H  I  J   K  L  M  N   O  P  Q  R   S  T  U  V   W  X  Y  Z
@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)