DatasheetsPDF.com

FPF2103 Dataheets PDF



Part Number FPF2103
Manufacturers Fairchild Semiconductor
Logo Fairchild Semiconductor
Description (FPF2100 - FPF2107) IntelliMAX Advanced Load Management Products
Datasheet FPF2103 DatasheetFPF2103 Datasheet (PDF)

www.DataSheet4U.com FPF2100-FPF2107 IntelliMAX™ Advanced Load Management Products May 2005 FPF2100-FPF2107 IntelliMAX™ Advanced Load Management Products Features 1.8 to 5.5V Input Voltage Range Controlled Turn-On 200mA and 400mA Current Limit Options Undervoltage Lockout Thermal Shutdown <1uA Shutdown Current Auto restart Fast Current limit Response Time 3us to Moderate Over Currents 20ns to Hard Shorts Fault Blanking General Description The FPF2100 through FPF2107 is a family of load switch.

  FPF2103   FPF2103


Document
www.DataSheet4U.com FPF2100-FPF2107 IntelliMAX™ Advanced Load Management Products May 2005 FPF2100-FPF2107 IntelliMAX™ Advanced Load Management Products Features 1.8 to 5.5V Input Voltage Range Controlled Turn-On 200mA and 400mA Current Limit Options Undervoltage Lockout Thermal Shutdown <1uA Shutdown Current Auto restart Fast Current limit Response Time 3us to Moderate Over Currents 20ns to Hard Shorts Fault Blanking General Description The FPF2100 through FPF2107 is a family of load switches which provide full protection to systems and loads which may encounter large current conditions. These devices contain a 0.125Ω current-limited P-channel MOSFET which can operate over an input voltage range of 1.8-5.5V. Switch control is by a logic input (ON) capable of interfacing directly with low voltage control signals. Each part contains thermal shutdown protection which shuts off the switch to prevent damage to the part when a continuous over-current condition causes excessive heating. When the switch current reaches the current limit, the part operates in a constant-current mode to prohibit excessive currents from causing damage. For the FPF2100-FPF2102 and FPF2104-FPF2106, if the constant current condition still persists after 10ms, these parts will shut off the switch and pull the fault signal pin (FLAGB) low. The FPF2100, FPF2101, FPF2104 and FPF2105, have an auto-restart feature which will turn the switch on again after 160ms if the ON pin is still active. The FPF2102 and FPF2106 do not have this auto-restart feature so the switch will remain off until the ON pin is cycled. For the FPF2103 and FPF2107, a current limit condition will immediately pull the fault signal pin low and the part will remain in the constant-current mode until the switch current falls below the current limit. For the FPF2100 through FPF2103, the minimum current limit is 200mA while that for the FPF2104 through FPF2107 is 400mA. These parts are available in a space-saving 5 pin SOT23 package. Applications PDAs Cell Phones GPS Devices MP3 Players Digital Cameras Peripheral Ports Hot Swap Supplies Typical Application Circuit TO LOAD VIN VOUT FPF2100 - FPF2107 OFF ON ON GND FLAGB ©2005 Fairchild Semiconductor Corporation FPF2100-FPF2107 Rev. D2 1 www.fairchildsemi.com FPF2100-FPF2107 IntelliMAX™ Advanced Load Management Products Functional Block Diagram VIN UVLO ON CONTROL LOGIC CURRENT LIMIT THERMAL SHUTDOWN VOUT FLAGB GND Pin Configuration VIN 1 GND ON 2 3 SOT23-5 4 FLAGB 5 VOUT Pin Description Pin 1 2 3 4 5 Name VIN GND ON FLAGB VOUT Ground ON Control Input Function Supply Input: Input to the power switch and the supply voltage for the IC Fault Output: Active LO, open drain output which indicates an over current supply, under voltage or over temperature state. Switch Output: Output of the power switch FPF2100-FPF2107 Rev. D2 2 www.fairchildsemi.com FPF2100-FPF2107 IntelliMAX™ Advanced Load Management Products Absolute Maximum Ratings Parameter VIN, VOUT, ON, FLAGB to GND Power Dissipation @ TA = 25°C (note 1) Operating Junction Temperature Storage Temperature Thermal Resistance, Junction to Ambient Electrostatic Discharge Protection HBM MM 4000 400 -40 -65 Min. -0.3 Max. 6 667 125 150 150 Unit V mW °C °C ° C/W V V Recommended Operating Range Parameter VIN Ambient Operating Temperature, TA Min. 1.8 -40 Max. 5.5 85 Unit V °C Electrical Characteristics VIN = 1.8 to 5.5V, TA = -40 to +85°C unless otherwise noted. Typical values are at VIN = 3.3V and TA = 25°C. Parameter Basic Operation Operating Voltage Quiescent Current Shutdown Current Latch-Off Current (note 2) On-Resistance ON Input Logic High Voltage ON Input Logic Low Voltage ON Input Leakage Off Switch Leakage FLAGB Output Logic Low Voltage FLAGB Output High Leakage Current Protections Current Limit Symbol VIN IQ ISHDN ILATCHOFF RON VIH VIL Conditions Min. 1.8 Typ. Max 5.5 Units V A IOUT = 0mA Von active VIN = 1.8 to 3.3V VIN = 3.3 to 5.5V 95 110 50 125 150 0.75 1.30 0.5 1.0 1 1 0.1 0.15 0.2 0.3 1 160 200 1 A A m V V A A V A mA VON = VIN, after an overcurrent fault TA = 25°C, IOUT = 50mA TA = -40 to +85°C, IOUT = 50mA VIN = 1.8V VIN = 5.5V VIN = 1.8V VIN = 5.5V VON = VIN or GND ISWOFF VON = 0V, VOUT = 0V VIN = 5V, ISINK = 10mA VIN = 1.8V, ISINK = 10mA VIN = 5V, Switch on ILIM VIN = 3.3V, VOUT = 3.0V FPF2100, FPF2101, FPF2102, FPF2103 FPF2104, FPF2105, FPF2106, FPF2107 200 300 400 400 600 800 Thermal Shutdown Shutdown Threshold Return from Shutdown Hysteresis 140 130 10 °C FPF2100-FPF2107 Rev. D2 3 www.fairchildsemi.com FPF2100-FPF2107 IntelliMAX™ Advanced Load Management Products Electrical Characteristics Cont. VIN = 1.8 to 5.5V, TA = -40 to +85°C unless otherwise noted. Typical values are at VIN = 3.3V and TA = 25°C. Parameter Protections Under Voltage Shutdown Under Voltage Shutdown Hysteresis Dynamic Turn on time Turn off time VOUT Rise Time VOUT Fall Time Over Current Blanking Time Auto-Restart Time Short Cir.


FPF2102 FPF2103 FPF2104


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)