Sweep Sensor. AT77C105A Datasheet

AT77C105A Sensor. Datasheet pdf. Equivalent


ATMEL Corporation AT77C105A
www.DataSheet4U.com
Features
Thermal Sensitive Layer Over a 0.35 µm CMOS Array
Image Zone: 0.4 x 11.6 mm
Image Array: 8 × 232 = 1856 Pixels
Pixel Pitch: 50 × 50 µm = 500 dpi Resolution
On-chip 8-bit Analog to Digital Converter
Serial Peripheral Interface (SPI) - 2 Modes:
– Fast Mode at 16 Mbps Max for Imaging
– Slow Mode at 200 kbps Max for Navigation and Control
Die Size: 1.5 × 15 mm
Operating Voltage: 2.3 to 3.6V
I/O Voltage: 1.65 to 3.6V
Operating Temperature Range: -40°C to 85°C
Finger Sweeping Speed from 2 to 20 cm/Second
Low Power: 4.5 mA (Image Acquisition), 1.5 mA (Navigation), <10 µA (Sleep Mode)
Hard Protective Coating (>4 Million Sweeps)
High Protection from Electrostatic Discharge
Small Form Factor Packaging
Description
Atmel’s AT77C105A fingerprint sensor is dedicated to PDA, cellular and smartphone
applications. Based on FingerChip thermal technology, the AT77C105A is a linear
sensor that captures fingerprint images by sweeping the finger over the sensing area.
This product embeds true hardware-based 8-way navigation and click functions as
well, as enabling elimination of mechanical joystick devices.
Applications
• Scrolling, Menu and Item Selection for PDAs, Cellular or Smartphone Applications
• Cellular and Smartphones-based Security (Device Protection, Network and ISP
Access, E-commerce)
• Personal Digital Agenda (PDA) Access
• User Authentication for Private and Confidential Data Access
• Portable Fingerprint Acquisition
FingerChip®
Thermal
Fingerprint
Sweep Sensor,
Hardware
Based
Navigation and
Click Functions,
Extended I/O
range (1.8-3.3V)
AT77C105A
Preliminary
Chip-on-board Package
Sweep your finger
to make life easier
Actual size of sensor
5419A–BIOM–01/05


AT77C105A Datasheet
Recommendation AT77C105A Datasheet
Part AT77C105A
Description FingerChip Thermal Fingerprint Sweep Sensor
Feature AT77C105A; www.DataSheet4U.com Features • • • • • • • • • • • • • • • Thermal Sensitive Layer Over a 0.35 µm C.
Manufacture ATMEL Corporation
Datasheet
Download AT77C105A Datasheet




ATMEL Corporation AT77C105A
Table 1. Pin Description for Chip-on-board Package: AT77C105A-CB08V
Pin Number Name
Type
Description
1 Not connected
2 Not connected
3 Not connected
4 Not connected
5
GNDD
G
Digital ground supply
6
GNDA
G
Analog ground supply - connect to GNDD
7
VDDD
P
Digital power supply
8
VDDA
P
Analog power supply - connect to VDD
9
SCK
I
Serial Port Interface (SPI) clock
10
TESTA
IO
Reserved for the analog test, not connected
11
MOSI
I
Master-out slave-in data
12
VDD_IO
P
Input/output power supply - connect IO voltage compatibility accordingly
13
MISO
O
Master-in slave-out data
14
SCANEN
I
Reserved for the scan test in factory, must be grounded
15 SSS I
Slow SPI slave select (active low
16 IRQ O
Interrupt line to host (active low). Digital test pin
17 FSS I
Fast SPI slave select (active low)
18 RST I
Reset and sleep mode control (active high)
19 FPL I
Front plane, must be grounded
Note: The die attach is connected to pin 6 and must be grounded. The FPL pin must also be grounded.
2 AT77C105A [Preliminary]
5419A–BIOM–01/05



ATMEL Corporation AT77C105A
5419A–BIOM–01/05
AT77C105A [Preliminary]
Figure 1. Typical Application
VDDD VDDD
10 k
10 k
IRQ
MISO
MOSI
SCK
SSS
FSS
SCANEN
GND
RST
VDD_IO
TESTA
VDD_IO
VDDD
GNDD
VDDA
GNDA
FPL
NC VDDD
10 µF
VDDA
10µF
GND
The pull-up must be implemented for the master controller. The noise should be lower
than 30 mV peak to peak on VDDA.
Figure 2. Pin Description
NC
NC
NC
NC
GNDD
GNDA
VDDD
VDDA
SCK
TESTA
MOSI
VDD_IO
MISO
SCANEN
SSS
IRQ
FSS
RST
FPL
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
The TESTA pin is only used for testing and debugging. The SCANEN pin is not used in
the final application and must be connected to ground.
Warning: SSS and FSS must never be low at the same time. When both SSS and FSS
equal 0, the chip switches to scan test mode. With the SPI protocol, this
configuration is not possible as only one slave at a time can be selected.
However, this configuration works when debugging the system.
3







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)