Polyester Capacitors. 225P Datasheet

225P Capacitors. Datasheet pdf. Equivalent

225P Datasheet
Recommendation 225P Datasheet
Part 225P
Description Polyester Capacitors
Feature 225P; Type 225P Vishay Sprague Polyester Capacitors Filmite® “E”, ORANGE DROP®, Radial Lead FEATURES • Ut.
Manufacture Vishay Siliconix
Datasheet
Download 225P Datasheet




Vishay Siliconix 225P
Type 225P
Vishay Sprague
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
PERFORMANCE CHARACTERISTICS
FEATURES
Utilizes minimum area where printed wiring
board space is most important
Wound from PETP polyester film and thin gauge RoHS
foil under carefully controlled atmospheric COMPLIANT
conditions
Protected against moisture by a conformal coating of
epoxy
Specifically designed for printed wiring board applications
Widely used in computers, instrumentation and
telecommunications equipment
100 VDC through 600 VDC, may be operated up to
+ 125 °C with proper dearting
Operating Temperature: - 55 °C to + 85 °C
Dielectric Withstanding Voltage:
To + 105 °C when working voltage is reduced to 70 % of
Capacitors shall withstand a DC potential of 250 % of rated
+ 85 °C rating; to + 125 °C when working voltage is reduced
voltage applied between terminals for not more than 5
to 50 % of 85 °C rating
seconds. The test voltage must be applied and discharged
Insulation Resistance: After a 2 minute charge at rated
through a resistor of 1 ohm per volt.
voltage or 500 V, whichever is less.
Humidity Test:
At + 25 °C: 100 000 Megohm for C 0.25 Microfarads
Condition capacitors with no voltage applied for 72 hours at
25000 Megohm - Microfarads for C > 0.25 Microfarads
95 % relative humidity and + 75 °C. Remove capacitors from
At + 85 °C: 10 000 Megohm for C 0.15 Microfarads
humidity chamber, wipe surface dry of moisture and dry in
1500 Megohm - Microfarads for C > 0.15 Microfarads www.DataSheet4U.ccomirculating air for 4 hours. Measure insulation resistance after
At + 105 °C: 1500 Megohm for C 0.17 Microfarads
a 2 minute charge at 25 °C and rated voltage or 500 VDC,
250 Megohm - Microfarads for C > 0.17 Microfarads
whichever is less. Minimum product of insulation resistance
At + 125 °C: 200 Megohm for C 0.13 Microfarads
and capacitance shall be 5000 Megohm - Microfarads after
25 Megohm - Microfarads for C > 0.13 Microfarads
test but need not exceed 10 000 Megohm. Not more than
one failure allowed in 12 units tested.
Capacitance Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000 Hz at
+ 25 °C or else be referred to measurements made at that
frequency and temperature. The maximum dissipation factor
shall be 0.75 %
DC Life Test:
Capacitance are capable of withstanding a 500 hour life test
at + 85 °C at 150 % of rated working voltage. After test,
capacitance shall not have changed by more than 5 % of
initial value, insulation resistance shall not have decreased
by more than 50 % of the initial limit and dissipation factor
shall not have increased to more than 1 %.
DIMENSIONS in inches [millimeters]
L
Max.
L
Max.
Lead
Length
0.237"
[6.020]
Max.
Lead
Length
0.237
[6.020]
Max.
H
Max.
L
Max.
Lead
Length
0.237
[6.020]
Max.
T Max.
S
± 0.060 [1.524]
Terminal A
CASE
CODE
W
X
Y
Document Number: 42016
Revision: 19-Feb-07
S
± 0.030 [0.762]
Terminal B
L
(Max.)
0.70 [17.78]
0.80 [20.32]
1.25 [31.75]
S
± 0.030 [0.762]
Terminal D
Tinned Copper-Clad Steel
0.032 [0.813] Dia.
(No. 20 AWG)
Terminal A and B
0.562 [14.275]
0.613 [15.570]
0.969 [24.613]
S
Terminal D
0.375 [9.525]
0.375 [9.525]
0.719 [18.263]
For technical questions, contact: spresale@vishay.com
www.vishay.com
25



Vishay Siliconix 225P
Type 225P
Vishay Sprague
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
CAPACITANCE CHANGE
16
14
12
10 CAPACITANCE CHANGE ENVELOPE
8 FOR 96 % CONFIDENCE LEVEL
6
4
2
0
2
4
6 - 55 - 40 - 25
- 50
0
+ 25 + 50 + 75 + 85 + 105 + 125
+ 100
TEMPERATURE DEG. CENTIGRADE
DISSIPATION FACTOR VS.TEMPERATURE
1.5
1.0
TYPICAL
0.5
0
- 55 - 40 - 25
- 50
0
+ 25 + 50 + 75 + 85 + 105 + 125
+ 100
TEMPERATURE DEG. CENTIGRADE
STANDARD RATINGS*
µF
± 10 % TOLERANCE
PART NUMBER
L
SIZE
H
T
100 VDC/70 VAC**
0.001
225P10291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0012
225P12291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0015
225P15291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0018
225P18291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0022
225P22291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0027
225P27291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0033
225P33291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0039
225P39291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0047
225P47291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0056
225P56291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0068
225P68291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.0082
225P82291W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.01
225P10391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.012
225P12391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.015
225P15391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.018
225P18391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.022
225P22391W
0.70 [17.78]
0.35 [8.89]
0.25 [6.35]
0.027
225P27391W
0.70 [17.78]
0.37 [9.40]
0.27 [6.86]
0.033
225P33391W
0.70 [17.78]
0.37 [9.40]
0.27 [6.86]
0.039
225P39391W
0.70 [17.78]
0.42 [10.67]
0.30 [7.62]
0.047
225P47391W
0.70 [17.78]
0.42 [10.67]
0.30 [7.62]
0.056
225P56391W
0.70 [17.78]
0.49 [12.45]
0.34 [8.64]
0.068
225P68391W
0.70 [17.78]
0.49 [12.45]
0.34 [8.64]
0.082
225P82391W
0.70 [17.78]
0.55 [13.97]
0.40 [10.16]
0.1
225P10491W
0.70 [17.78]
0.55 [13.97]
0.40 [10.16]
0.12
225P12491X
0.80 [20.32]
0.57 [14.48]
0.37 [9.40]
0.15
225P15491X
0.80 [20.32]
0.62 [15.75]
0.40 [10.16]
0.18
225P18491X
0.80 [20.32]
0.66 [16.76]
0.43 [10.92]
0.22
225P22491X
0.80 [20.32]
0.70 [17.78]
0.46 [11.68]
0.27
225P27491X
0.80 [20.32]
0.74 [18.80]
0.49 [12.45]
0.33
225P33491X
0.80 [20.32]
0.77 [19.56]
0.52 [13.21]
0.39
225P39491X
0.80 [20.32]
0.81 [20.57]
0.55 [13.97]
0.47
225P47491X
0.80 [20.32]
0.86 [21.84]
0.60 [15.24]
0.56
225P56491Y
1.25 [31.75]
0.88 [22.35]
0.55 [13.97]
0.68
225P68491Y
1.25 [31.75]
0.90 [22.86]
0.58 [14.73]
0.82
225P82491Y
1.25 [31.75]
0.94 [23.88]
0.65 [16.51]
1.0
225P10591Y
1.25 [31.75]
0.98 [24.89]
0.72 [18.29]
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See Ordering Information (Ex: 225P39391WD3).
** 60 Hz rms
www.vishay.com
26
For technical questions, contact: spresale@vishay.com
Document Number: 42016
Revision: 19-Feb-07



Vishay Siliconix 225P
Polyester Capacitors
Filmite® “E”, ORANGE DROP®, Radial Lead
Type 225P
Vishay Sprague
STANDARD RATINGS* in inches [millimeters]
µF
± 10 % TOLERANCE
PART NUMBER
L
SIZE
H
T
200 VDC/140 VAC**
0.001
225P10292X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0015
225P15292X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0022
225P22292X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0033
225P33292X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0047
225P47292X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0068
225P68292X
0.80 [20.32]
0.58 [14.73]
0.25 [6.35]
0.01
225P10392X
0.80 [20.32]
0.58 [14.73]
0.25 [6.35]
0.015
225P15392X
0.80 [20.32]
0.58 [14.73]
0.25 [6.35]
0.022
225P22392X
0.80 [20.32]
0.58 [14.73]
0.25 [6.35]
0.033
225P33392X
0.80 [20.32]
0.61 [15.49]
0.28 [7.11]
0.047
225P47392X
0.80 [20.32]
0.61 [15.49]
0.28 [7.11]
0.068
225P68392X
0.80 [20.32]
0.64 [16.26]
0.31 [7.87]
0.1
225P10492X
0.80 [20.32]
0.71 [18.03]
0.37 [9.40]
0.1
225P10492Y
1.25 [31.75]
0.64 [16.26]
0.31 [7.87]
0.15
225P15492X
0.80 [20.32]
0.74 [18.80]
0.41 [10.41]
0.22
225P22492X
0.80 [20.32]
0.77 [19.56]
0.48 [12.19]
0.33
225P33492Y
1.25 [31.75]
0.71 [18.03]
0.41 [10.41]
0.47
225P47492Y
1.25 [31.75]
0.83 [21.08]
0.50 [12.70]
0.68
225P68492Y
1.25 [31.75]
1.14 [28.96]
0.84 [21.34]
400 VDC/200 VAC**
0.001
225P10294X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0015
225P15294X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0022
225P22294X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0033
225P33294X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0047
225P47294X
0.80 [20.32]
0.55 [13.97]
0.25 [6.35]
0.0068
225P68294X
0.80 [20.32]
0.58 [14.73]
0.25 [6.35]
0.01
225P10394X
0.80 [20.32]
0.58 [14.73]
0.28 [7.11]
0.015
225P15394X
0.80 [20.32]
0.58 [14.73]
0.28 [7.11]
0.022
225P22394X
0.80 [20.32]
0.58 [14.73]
0.31 [7.87]
0.033
225P33394X
0.80 [20.32]
0.65 [16.51]
0.34 [8.64]
0.047
225P47394X
0.80 [20.32]
0.65 [16.51]
0.41 [10.41]
0.047
225P47394Y
1.25 [31.75]
0.64 [16.26]
0.31 [7.87]
0.068
225P68394X
0.80 [20.32]
0.80 [20.32]
0.47 [11.94]
0.1
225P10494X
0.80 [20.32]
0.84 [21.34]
0.52 [13.21]
0.1
225P10494Y
1.25 [31.75]
0.74 [18.80]
0.41 [10.41]
0.15
225P15494Y
1.25 [31.75]
0.80 [20.32]
0.47 [11.94]
0.22
225P22494Y
1.25 [31.75]
0.89 [22.61]
0.56 [14. 22]
0.33
225P33494Y
1.25 [31.75]
0.99 [25.15]
0.72 [18.29]
0.47
225P47494Y
1.25 [31.75]
1.14 [28.96]
0.84 [21.34]
* Parts ordered with D3 leads are standard capacitors in stock and available through the Sprague® Distribution Network. For complete Part
Number, add letter and number for terminal and lead length. See How to Order (Ex: 225P39391WD3).
** 60 Hz rms
Document Number: 42016
Revision: 19-Feb-07
For technical questions, contact: spresale@vishay.com
www.vishay.com
27







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)