DC/DC Converters. SMFL Datasheet


SMFL Converters. Datasheet pdf. Equivalent


SMFL


Single and Dual DC/DC Converters
Crane Aerospace & Electronics Power Solutions

SMFL Single and Dual DC/DC Converters
28 Volt input – 65 Watt
Features
•	 Fully qualified to Class H or K •	 –55° to +125°C operation •	 16 to 40 VDC input •	 Fully Isolated •	 Magnetic feedback

•	 Fixed frequency, 600 kHz typical

•	 Topology – Single Ended Forward •	 Inhibit input side and output side •	 Sync function

•	 50 V for up to 120 ms transient protection

VDC Output single 3.3 5 12 15 dual ±5 ±12 ±15

models

•	 Output trim on single output models •	 Indefinite short circuit protection •	 Up to 85% efficiency / 43 W/in3 •	 Parallelable up to 148 watts •	 Remote sense on single output models

The SMFL Series™ 28-volt DC/DC converters are rated up to 65 watts output power over a -55° to +125°C ­temperature range with a 28 Vdc nominal input. On dual output models up to 70% of the rated output power can be drawn from either the positive or negative outputs. Current sharing allows the units to be paralleled for total power of up to 148 watts. The welded, hermetically sealed package is only 3.0 x 1.5 x 0.40 www.DataSheet4U.com inches, giving the series an overall power density of up to 45 watts per cubic inch.

description

Inhibit

Screening

SMFL converters offer the following screening options: Space Prototype (O), Class H, or Class K. Radiation tolerant to Radiation Hardness Assurance (RHA) levels of “-” (O) or “R”, per ...



SMFL
Crane Aerospace & Electronics Power Solutions
SMFL Single and Dual DC/DC Converters
28 Volt input – 65 Watt
Features
• Fully qualified to Class H or K
• –55° to +125°C operation
• 16 to 40 VDC input
• Fully Isolated
• Magnetic feedback
• Fixed frequency, 600 kHz typical
• Topology – Single Ended Forward
• 50 V for up to 120 ms transient protection
• Inhibit input side and output side
• Sync function
• Output trim on single output models
• Indefinite short circuit protection
• Remote sense on single output models
• Up to 85% efficiency / 43 W/in3
• Parallelable up to 148 watts
models
VDC Output
single
3.3
5
12
15
dual
±5
±12
±15
description
The SMFL Series™ 28-volt DC/DC converters are rated up to 65 watts
output power over a -55° to +125°C ­temperature range with a 28 Vdc
nominal input. On dual output models up to 70% of the rated output
power can be drawn from either the positive or negative outputs. Current
sharing allows the units to be paralleled for total power of up to 148
www.DataSheet4wU.acotmts. The welded, hermetically sealed package is only 3.0 x 1.5 x 0.40
inches, giving the series an overall power density of up to 45 watts per
cubic inch.
Screening
SMFL converters offer the following screening options: Space Prototype
(O), Class H, or Class K. Radiation tolerant to Radiation Hardness
Assurance (RHA) levels of “-” (O) or “R”, per MIL-STD-38534. Interpoint
model numbers use an “O” in the RHA designator position to indicate the
“-” (dash) Radiation Hardness Assurance level of MIL-PRF-38534, which
is defined as “no RHA”. See “Class H and K, QML Screening” tables for
more information.
Design Features
SMFL Series converters are switching regulators that use a quasi-square
wave, single ended forward converter design with a constant switching
frequency of 600 kHz typical.
Isolation between input and output circuits is provided with a transformer
in the forward path and a wide bandwidth magnetic coupling in the feed-
back control loop. The SMFL uses a unique dual loop feedback technique
that controls output current with an inner feedback loop and an output
voltage with a cascaded voltage mode feedback loop. The additional
secondary current mode feedback loop improves transient response in
a manner similar to primary current mode control and allows for ease of
paralleling, but without the cost and complexity.
The constant frequency, pulse-width modulated converters use a quasi-
square wave single-ended forward design. Tight load regulation is
achieved through a wide-bandwidth magnetic feedback circuit. The output
voltage on single SMFL models can be trimmed to a specific output
voltage by adding an external resistor.
Inhibit
The SMFL Series converters have two TTL compatible inhibit terminals
(INH1 and INH2) that can be used to disable power conversion, resulting
in a very low quiescent input current and no generation of switching
noise. An open collector TTL compatible low (<0.8 volts) is required to
inhibit the converter between INH1 (pin 4) and Input Common (pin 2). An
open collector TTL compatible low (<0.5 volts) is required to inhibit the
converter between INH2 (pin 12) and Output Common (pin 8). The appli-
cation of intermediate voltages to these pins (1.5 to 10.5 volts) should be
avoided.
Sync
Converters may be synced to an external clock (525 to 675 kHz) or
to one another by using the sync in or out pins. The nominal free-run
switching frequency is 600 kHz.
Current and Parallel Operation
Multiple single output SMFL converters may be used in parallel to drive a
common load. In this mode of operation the load current is shared by two
or three SMFL converters. In current sharing mode, one SMFL converter
is designated as a master. The SLAVE pin (pin 11) of the master is left
unconnected and the MSTR/INH2 pin (pin 12) of the master is connected
to the SLAVE pin (pin 11) of the slave units. The units designated as
slaves have the MSTR/INH2 pin (pin 12) connected to the SNS RTN
pin (pin 9). Note that synchronizing the units together is not required for
current sharing operation. A second slave unit may be placed in parallel
with a master and slave; this requires the TRI pin (pin 3) of the master
unit to be connected to the SNS RTN pin (pin 9). See Figure 2 for a block
diagram of parallel connections.
When paralleled, 76% of the total combined power ratings of the SMFL
converters are available at the load. Overload and short circuit perfor-
mance are not adversely affected during parallel ­operation.
Crane Aerospace & Electronics
Electronics Group (Interpoint Brand)
PO Box 97005 • Redmond WA 98073-9705
425.882.3100 • electronics@craneae.com
www.craneae.com
Page  of 13
Rev H - 20061102

SMFL
Crane Aerospace & Electronics Power Solutions
SMFL Single and Dual DC/DC Converters
28 Volt input – 65 Watt
SINGLE OUTPUT MODELS CONNECTION DIAGRAMS - SENSE AND PARALLEL
+
28V
Inhibit
Sync In
+
28V
Inhibit
Sync In
1 Positive Input
2 Input Common
3 TR1
4 INH1
5 Sync Out
6 Sync In
MSTR/INH2 12
Slave 11
Pos. Sense 10
Sense Return
Output Common
Positive Output
9
8
7
REMOTE SENSE CONNECTION
1 Positive Input
2 Input Common
3 TR1
4 INH1
5 Sync Out
6 Sync In
MSTR/INH2 12
Slave 11
Pos. Sense 10
Sense Return
Output Common
Positive Output
9
8
7
OUTPUT VOLTAGE ADJUST CONNECTION
VOUT INCREASE
(VOLT)
0.1
0.2
0.3
0.4
0.5
3.3-V
120
240
360
480
600
RA (OHMS)
5–V 12–V
70 25
140 50
210 75
280 100
350 125
15–V
20
40
60
80
100
RA
Figure 1: Sense Connections and Trim Table
+
RL
+
RL
+
28V
Inhibit
Sync In
1 Positive Input
MSTR/INH2 12
2 Input Common
Slave 11
3 TR1
4 INH1
5 Sync Out
6 Sync In
MASTER
Pos. Sense 10
Sense Return 9
Output Common 8
Positive Output 7
CONNECT ONLY WHEN 2 SLAVES ARE USED
1 Positive Input
MSTR/INH2 12
2 Input Common
Slave 11
3 TR1
4 INH1
Pos. Sense 10
SLAVE 1 Sense Return 9
5 Sync Out
6 Sync In
Output Common 8
Positive Output 7
1 Positive Input
MSTR/INH2 12
2 Input Common
Slave 11
3 TR1
4 INH1
5 Sync Out
6 Sync In
Pos. Sense 10
SLAVE 2 Sense Return 9
Output Common 8
Positive Output 7
Figure 2: Parallel Connections
+
RL
www.craneae.com
Page  of 13
Rev H - 20061102




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)