Biasable Mixer. MDC-163 Datasheet

MDC-163 Mixer. Datasheet pdf. Equivalent

Part MDC-163
Description Termination-Insensitive Biasable Mixer
Feature www.DataSheet4U.com Termination-Insensitive Biasable Mixer, 1 - 6 GHz Features • LO Drive: 0 dBm • .
Manufacture Tyco Electronics
Total Page 3 Pages
Datasheet
Download MDC-163 Datasheet



MDC-163
www.DataSheet4U.com
Termination-Insensitive Biasable Mixer,
1 - 6 GHz
Features
LO Drive: 0 dBm
Intermodulation Ratio Insensitive to
IF Ports Mismatches
Conversion Loss: 7 dB Typical Midband
Impedance: 50 Ohms Nominal
Maximum Input Power: 500 mW max. @ 25°C,
Derated 6.4 mW/°C
Low Power: +24 dBm Max.
DC Bias: +5, -5 VDC @12 mA each
MIL-STD-883 Screening Available
Description
The unique design of the termination insensitive
mixer (TIM) enables it to apply high reverse voltage
to diodes during their “off” phase, in the LO cycle.
This allows for higher power level performance with
minimum distortion. In addition the TIM has internal
loads that provide a good match and also absorb
mixer generated LO frequency terms. Combined,
these features give the mixer its insensitivity to
external mismatches, plus superior VSWR. Applied
bias allows this mixer to perform at low LO power
levels.
C-2
MDC-163
V3
1
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
North America Tel: 800.366.2266 / Fax: 978.366.2266
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.



MDC-163
Termination-Insensitive Biasable Mixer,
1 - 6 GHz
Electrical Specifications1: TA = -55°C to +85°C
Parameter
Frequency Range
Conversion Loss2
Test Conditions
RF, LO Ports
IF Port
Frequency
1-6
10 - 2000
1 - 3 GHz
1 - 6 GHz
Isolation
LO to RF
1 - 2 GHz
2 - 6 GHz
LO to IF
1 - 6 GHz
MDC-163
V3
Units
Min
Typ
Max
GHz
MHz
dB
dB
——
——
— 9.0
— 10.5
dB 10 — —
dB 13 — —
dB 13 — —
RF to IF
RF Input
SSB Noise Figure
3rd Order Input
Intercept
1 dB Compression
1 dB Desensitization
Within 1 dB of Conversion Loss
Max.
3rd Order Intercept
Degration
@ IF Termination VSWR 3:1
1 - 6 GHz
2.0 GHz
4.0 GHz
6.0 GHz
dB 15 — —
dBm
-2
dBm
-6
— ———
dBm
7.0
dBm
8.0
dBm
5.0
dB — 1.5 —
1. All specifications apply when operated at +0 dBm available LO power with 50 ohm source and load impedance.
2. For IF frequencies of 10 - 500 MHz and an RF of –10 dBm or lower.
3. Independent of sum frequency match.
This product contains elements protected by United States Patent Number 4,224,572
2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
North America Tel: 800.366.2266 / Fax: 978.366.2266
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)