SP6T Switch. SW90-0004A Datasheet

SW90-0004A Switch. Datasheet pdf. Equivalent

Part SW90-0004A
Description GaAs SP6T Switch
Feature www.DataSheet4U.com GaAs SP6T Switch, Absorptive, Single Supply DC - 4.0 GHz Features • • • • • • •.
Manufacture Tyco Electronics
Total Page 4 Pages
Datasheet
Download SW90-0004A Datasheet



SW90-0004A
www.DataSheet4U.com
GaAs SP6T Switch, Absorptive, Single Supply
DC - 4.0 GHz
SW90-0004A
V7
Features
Operates DC - 4 GHz on Single Supply
ASIC TTL / CMOS Driver
Leadless 4 x 7 mm Chip Scale Plastic Package
Low DC Power Consumption
50 Ohm Nominal Impedance
Test Boards are Available
Tape and Reel are Available
Description
M/A-COM's SW90-0004A is a SP6T absorptive
pHEMT switch with integral TTL driver. This device
is in an MLP plastic surface mount package. This
switch offers excellent broadband performance and
repeatability from DC to 4 GHz, while maintaining
low DC power dissipation. The SW90-0004A is
ideally suited for wireless infrastructure applications.
Ordering Information
Part Number
SW90-0004A
SW90-0004ATR
SW90-0004A-TB
Package
Bulk Packaging
1000 piece reel
Units Mounted on Test Board
Note: Reference Application Note M513 for reel size
information.
Absolute Maximum Ratings 1,2
Parameter
Max. Input Power
0.05 GHz
0.5 - 4.0 GHz
Bias Voltages
VCC
Control Voltage 3
Operating Temperature
Storage Temperature
Absolute Maximum
+27 dBm
+34 dBm
+5.5V
-0.5V to VCC +0.5V
-40°C to +85°C
-65°C to +125°C
1. Operation of this device above any one of these parameters
may cause permanent damage.
2. When the RF input is applied to the terminated port, the
absolute maximum power is +30 dBm.
3. Standard CMOS TTL interface, latch-up will occur if logic
signal is applied prior to power supply.
Functional Schematic
Pin Configuration 4,5,6
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Function
CP2
VEE
NC
C6
C5
C4
C3
C2
C1
NC
GND
NC
GND
RF1
GND
RF2
GND
RF3
Pin No.
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Function
GND
NC
GND
RFC
GND
GND
RF4
GND
RF5
GND
RF6
GND
NC
VEE
Vcc
NC
Vcc
CP1
4. NC = No Connection
5. For single supply operation VEE is internally generated and
must remain isolated from external power supplies.
Generated noise is typical of switching DC-DC Converters.
6. Connections and external components shown in functional
schematic are required. 0.1µF Capacitors need to be located
near pins 32 & 33.
1
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
North America Tel: 800.366.2266 / Fax: 978.366.2266
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.



SW90-0004A
GaAs SP6T Switch, Absorptive, Single Supply
DC - 4.0 GHz
SW90-0004A
V7
Electrical Specifications: TA = 25°C
Parameter
Test Conditions
Insertion Loss
RFC-RF1, 2, 3, 4, 5, 6
Isolation
VSWR
1 dB Compression
Input IP3
On (RFC, RF1-RF6)
Logic per Truth Table
Off (RF1-RF6)
Logic per Truth Table
Two-tone inputs up to +5 dBm
Switching Speed
Vcc
Logic “0”
Logic “1”
Icc 7
Turn-on Current 8
Switching Noise
Thermal Resistance θjc
Ton (50% Control to 10% RF)
Toff (50% Control to 90% RF)
Trise (10% to 90% RF)
Tfall (90% to 10% RF)
Sink Current is 20 µA max.
Source Current is 20 µA max.
Vcc min to max, Logic “0” or “1”
For guaranteed start-up
Generated from
DC-DC Converter with
recommended capacitors
Frequency
DC - 3.0 GHz
3.0 - 4.0 GHz
DC - 4.0 GHz
DC - 4.0 GHz
DC - 4.0 GHz
50 MHz
0.5 - 4.0 GHz
50 MHz
0.5-4.0 GHz
3.5 MHz
Units
dB
dB
dB
Ratio
Ratio
dBm
dBm
dBm
dBm
nS
nS
nS
nS
V
V
V
mA
mA
dBm
Min.
25
4.5
0.0
2.0
°C/W
Typ.
15
27
30
40
20
15
5
2
5.0
5
-93
Max.
2.1
2.4
2.0:1
2.0:1
5.5
0.8
5.0
8
125
15 —
7. During turn-on, the device requires an initial start up current (Icc) specified as “Turn-on Current”. Once operational, Icc will drop to the
specified levels. This is not applicable to dual supply operation.
8. The DC-DC converter is guaranteed to start in 100 µs as long as the power supplies have the maximum turn-on current available for
start-up.
Truth Table
Control Inputs
Condition of Switch
"0" is TTL Low, "1" is TTL High
RF Common to Each RF Port
C1
C2
C3
C4
C5
C6
RF1
RF2
RF3
RF4 RF5 RF6
1 0 0 0 0 0 On Off Off Off Off Off
0 1 0 0 0 0 Off On Off Off Off Off
0 0 1 0 0 0 Off Off On Off Off Off
0 0 0 1 0 0 Off Off Off On Off Off
0 0 0 0 1 0 Off Off Off Off On Off
0 0 0 0 0 1 Off Off Off Off Off On
2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
North America Tel: 800.366.2266 / Fax: 978.366.2266
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)