Document
www.DataSheet4U.com
PQxxxGN01ZPH Series
PQxxxGN01ZPH Series
Low Voltage Operation,Compact Surface Mount type Low Power-Loss Voltage Regulators
Features
1.Low voltage output (VO=0.8 to 1.2V) 2.Low voltage operation: VIN(MIN)=1.7V 3.Output current : 1A 4.Built-in overcurrent and overheat protection functions 5.Conform to Flow Soldering SC-63 package 6.RoHS directive compliant
■ Outline Dimensions
(Unit : mm)
Lead finish identification mark
6.6MAX. 5.2±0.5
3
2.1±0.5
(0.3)
2.5MIN. 5.5±0.5 0.7 MAX.
008GN01
H
Epoxy resin
9.7MAX.
(0~0.25) (0.3)
Applications
1.AV equipment 2.OA equipment
1 2 4 5
4-(1.27)
(
) : Typical dimensions
Product mass:(0.23g)
Model Line-up
Output Voltage (TYP.)
0.8V 1.0V 1.2V
1
3
2
Specific IC
5
Model No.
1
PQ008GN01ZPH PQ010GN01ZPH PQ012GN01ZPH
2 3 4 5
DC input (VIN) Bias input (VB) DC output (VO) NC GND
Lead finish:Lead-free solder plating (Composition: Sn2Cu)
Absolute Maximum Ratings
(Ta=25°C) Parameter Symbol *1 VIN Input voltage *1 Bias supply voltage VB IO Output current *2 Power dissipation PD *3 Junction temperature Tj Operating temperature Topr Tstg Storage temperature Tsol Soldering temperature Rating Unit V 5.5 7 V A 1 8 W 150 °C °C -40 to +85 -40 to +150 °C °C 260(10s)
*1 All are open except GND and applicable terminals. *2 PD:With infinite heat sink *3 Overheat protection may operate at Tj:125°C to 150°C
Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
Sheet No.: OP06052A
(0.9)
0.3 +0.2 -0.1
(1.7)
PQxxxGN01ZPH Series Electrical Characteristics
Parameter Input voltage Bias supply voltage Output voltage Load regulation Line regulation Temperature coefficient of output voltage Ripple rejection Bias inflow current Symbol VIN VB VO RegL RegI TCVO RR1 RR2 IB
(Unless otherwise specified,condition shall be VIN=1.8V,VB=3.3V,IO=0.5A,Ta=25°C)
Conditions
MIN. 1.7 2.35
TYP.
MAX. 5.5 7 0.5 0.7
Unit V V V % % %/°C dB dB mA
IO=5mA to 1A
VIN=1.7V to 5.5V,VB=2.35 to 7V , IO=5mA
0.2 0.3 ±0.5 60 53 1.5
Refer to the following table.1
Tj=0 to +125°C, IO=5mA Refer to Fig.2 Refer to Fig.3
-
-
2
Table.1 Output Voltage
(Unless otherwise specified,condition shall be VIN=1.8V,VB=3.3V,IO=0.5A,Ta=25°C)
Model No. PQ008GN01ZPH PQ010GN01ZPH PQ012GN01ZPH
Symbol VO
Conditions -
MIN. 0.77 0.97 1.17
TYP. 0.8 1 1.2
MAX. 0.83 1.03 1.23
Unit V
Fig.1 Test Circuit
VO
1
3 A IO
VIN 1μF
VB A IB
2 5 10μF V RL
1μ F
Fig.2 Test Circuit for Ripple Rejection (1)
+ 1 ei ~ VB VIN 1.8V 3.3V 1μ F 1μF 2 5 10μF RL 3 IO eo
V ~
f=120Hz(sine wave) ei(rms)=0.1V VIN=1.8V VB=3.3V IO=0.3A RR=20log(ei(rms)/eo(rms))
Sheet No.: OP06052A
2
PQxxxGN01ZPH Series
Fig.3 Test Circuit for Ripple Reje.