Document
www.DataSheet4U.com
PQxxxEZ1HZxH Series
PQxxxEZ1HZxH Series
Low Voltage Operation Low Power-Loss Voltage Regulators
Features
1.Low voltage operation (Minimum operating voltage: 2.35V) 2.5V input → available 1.5 to 1.8V 2.Low dissipation current Dissipation current at no load: MAX. 2mA Output OFF-state dissipation current: MAX. 5μA 3.Low power-loss 4.Built-in overcurrent and overheat protection functions 5.RoHS directive compliant
■ Outline Dimensions
(Unit : mm)
6.6MAX. 5.2
±0.5 3
2.3±0.5 (0.5)
Epoxy resin
9.7MAX.
5.5±0.5
0 1 5 EZ1 H
Lead finish identification mark
1.Power supplies for personal computers and peripheral equipment 2.Power supplies for various electronic equipment such as DVD player or STB
1 2 3 4 5
4–(1.27)
(
) : Typical dimensions
Product mass:(0.3g)
Model Line-up
1 3
Output current
Package type Taping Sleeve Taping Sleeve
Output voltage
Specific IC
1.5V
1.8V
2.5V
1 2 3 4 5
2 5
1.5A
PQ015EZ1HZPH PQ018EZ1HZPH PQ025EZ1HZPH PQ015EZ1HZZH PQ018EZ1HZZH PQ025EZ1HZZH
3.0V
3.3V
1.5A
PQ030EZ1HZPH PQ033EZ1HZPH PQ030EZ1HZZH PQ033EZ1HZZH
DC input (VIN) ON/OFF control terminal (VC) DC output(VO) NC GND
Lead finish:Lead-free solder plating (Composition: Sn2Cu)
Absolute Maximum Ratings
(Ta=25°C) Symbol VIN *1 ON/OFF control terminal voltage VC IO Output current *2 Power dissipation PD *3 Junction temperature Tj Operating temperature Topr Tstg Storage temperature Tsol Soldering temperature
*1
Parameter Input voltage
Rating Unit V 10 10 V A 1.5 8 W 150 °C °C -40 to +85 -40 to +150 °C °C 260(10s)
*1 All are open except GND and applicable terminals. *2 PD: With infinite heat sink *3 Overheat protection may operate at Tj:125°C to 150°C
Notice The content of data sheet is subject to change without prior notice. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
Sheet No.: OP06051
(0.9 )
Applications
2.5
MIN.
(0 ~0.25)
+0.2 0.5–0.1
(0.5)
(1.7 )
H
PQxxxEZ1HZxH Series Electrical Characteristics
(Unless otherwise specified, condition shall be VIN=VO(TYP.)+1V, IO=0.5A,VC=2.7V, Ta=25˚C)
Parameter Input voltage
Output voltage Load regulation Line regulation Temperature coefficient of output voltage Ripple Rejection
4 6
Symbol
VIN
Conditions
MIN.
TYP.
MAX.
VO RegL RegI TCVO RR VI-O VC(ON) IC(ON) VC(OFF) IC(OFF) Iq Iqs
- - IO=5mA to 1.5A
VIN=VO(TYP.)+1V to VO(TYP.)+6V
Refer to the table 1 Refer to the table 2
Unit V V % % %/°C dB V V μA V μA mA μA
- - - 45 - 2.0 - - - - -
0.2 0.1
±0.01
Tj=0 to 125°C, IO=5mA Refer to Fig.2
5
Dropout voltage
ON-state voltage for control ON-state current for control OFF-state voltage for control OFF-state current for control Quiescent current Output OFF-state dissipation current
IO=1.25A - - -
60 - - - - -
1
2.0 1.0 - - 1.