DatasheetsPDF.com

1000P2 Dataheets PDF



Part Number 1000P2
Manufacturers Winget
Logo Winget
Description Turvomixer
Datasheet 1000P2 Datasheet1000P2 Datasheet (PDF)

www.DataSheet4U.com OPERATION, MAINTENANCE & SPARE PARTS 1000P2 TURBOMIXER PRINTED SEPTEMBER 1977 REPRINTED APRIL 2003 UPTO M/C No 999 WINGET LIMITED PO BOX 41 EDGEFOLD INDUSTRIAL ESTATE PLODDER LANE BOLTON LANCS BL4 OLS TEL: ++ 44 (0) 1204 854650 FAX: ++ 44 (0) 1204 854663 [email protected] [email protected] www.winget.co.uk www.DataSheet4U.com TURBOMIXER 1000P2 This manual is a reprint of the Winget publication No S108 last printed during September 1977, applicable upto M/C S/No 999 a.

  1000P2   1000P2


Document
www.DataSheet4U.com OPERATION, MAINTENANCE & SPARE PARTS 1000P2 TURBOMIXER PRINTED SEPTEMBER 1977 REPRINTED APRIL 2003 UPTO M/C No 999 WINGET LIMITED PO BOX 41 EDGEFOLD INDUSTRIAL ESTATE PLODDER LANE BOLTON LANCS BL4 OLS TEL: ++ 44 (0) 1204 854650 FAX: ++ 44 (0) 1204 854663 [email protected] [email protected] www.winget.co.uk www.DataSheet4U.com TURBOMIXER 1000P2 This manual is a reprint of the Winget publication No S108 last printed during September 1977, applicable upto M/C S/No 999 and contains some amended part numbers. Winget Limited operate a policy of continuous product development. Therefore, some illustrations or text within this publication may differ from your machine. The contents of this manual although correct at the time of publication, may be subject to alteration by the manufacturers without notice and Winget Limited can accept no responsibility for any errors or omissions contained within the following pages. Nor can we accept any liability whatsoever arising from the use of this manual howsoever caused. www.DataSheet4U.com II CONTENTS Section INTRODUCTION Introduction Warranty SAFE WORKING Safe Working Permit to work systems INSTALLATION General Air Operated Discharge Doors Pre-running checks OPERATION Mixing Discharging Discharge Door Turbo Mixer Covers Trapped Key Interlock System Cleaning the Mixer OVERHAUL & MAINTENANCE INSTRUCTIONS Lubrication Gear Box Topping Up Oil Change Air Operated Discharge Door Adjustment of Mixer & Scraper Blades Pre-loading of Mixer Arm Springs Fitting New Blades Replacement of Wearing Plates Rotor Gearbox & Motor Replacement Discharge Door Cylinder Maintenance Service Schedule 4.1 4.1 4.1 4.1 4.2 4.2 4.3 4.3 4.4 4.5 4.6 3.1 3.1 3.2 3.3 3.4 2.1 2.1 2.1 1.1 1.2 III IV Page Section INTRODUCTION Page TECHNICAL INFORMATION Specification Dimensions PARTS Spares Groups 5.1 5.2 6.1 6.2 www.DataSheet4U.com INTRODUCTION THE HANDBOOK WARNING The operator must read all the Handbook and fully understand its contents before attempting to operate the machine. III THE HANDBOOK MUST BE AVAILABLE TO THE OPERATOR AT ALL TIMES. The Handbook must be kept clean and in good condition. Additional copies of the Handbook can be obtained from Winget Limited. The contents of this Operator's Handbook are designed as a guide to the machine's controls, operation, working capacities and maintenance. It is not a training manual. Only trained operators should use this machine. Contact the C.I.T.B. or equivalent body for advice on training. The operating instructions and maintenance recommendations contained in this book will enable you to become familiar with your mixer to obtain the best results in the shortest possible time. The life and trouble free running of your machine will depend largely on the care it receives. It is your responsibility to ensure that the maintenance instructions outlined in this book are carried out. When replacements are required, it is essential that only genuine Winget parts are used and that any repair or servicing work is carried out by competent fitters. In this Handbook are WARNING notes. They are preceded by this symbol: WARNING These notes are used to indicate the procedure being described in the Handbook must be followed to avoid serious injury or death to yourself or to others; or damage to the machine. The warnings are also used to protect the machine from unsafe servicing practices. Pay particular attention to the warnings given in the Handbook. If you have any doubts about any aspect of the machine's capability or servicing procedures, you must consult the manufacturer. www.DataSheet4U.com IV WARRANTY INTRODUCTION As every reasonable care is taken that goods of this Company's manufacture shall be free from defect in material and workmanship, the Company will supply free to any destination in the British Isles named in the tender or F.O.B. British Ports in the case of goods situated abroad, any part or parts which, under normal service, appears to the Company's satisfaction to have been at the time of delivery defect in such parts, provided it is notified thereof within twelve months or 2,000 working hours from the date of delivery (whichever shall be the earlier) or, where the Company is responsible for erection, within twelve months from the date on which the customer is notified that any plant or machinery is ready for starting up provided that:a) Written notice is given to the Company within seven days of the discovery of the defect. b) Unless otherwise agreed, the alleged defective part or parts are returned to the Company's Works carriage paid and its inspection establishes the claim. Replaced parts shall become the property of the Company. c)No part which is not of the Company's manufacture has been fitted, otherwise than by it or on its behalf, or with its written approval. d) No unauthorised alteration or modification has been made to the machine or component the subject of the claim. In no cases shall the Company be .


LS4558N 1000P2 SM8720AV


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)