DatasheetsPDF.com

596287775 Dataheets PDF



Part Number 596287775
Manufacturers ETC
Logo ETC
Description Standard Microcircuit Drawing
Datasheet 596287775 Datasheet596287775 Datasheet (PDF)

www.DataSheet4U.com REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Technical changes to table 1. Editorial changes throughout. Drawing updated to reflect current requirements. - gt. 81-09-30 N.A. Hauck B 04-06-18 R. Monnin REV SHEET REV SHEET REV STATUS OF SHEETS PMIC N/A REV SHEET PREPARED BY B 1 B 2 B 3 B 4 B 5 B 6 B 7 B 8 B 9 Marcia B. Kelleher STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT.

  596287775   596287775


Document
www.DataSheet4U.com REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Technical changes to table 1. Editorial changes throughout. Drawing updated to reflect current requirements. - gt. 81-09-30 N.A. Hauck B 04-06-18 R. Monnin REV SHEET REV SHEET REV STATUS OF SHEETS PMIC N/A REV SHEET PREPARED BY B 1 B 2 B 3 B 4 B 5 B 6 B 7 B 8 B 9 Marcia B. Kelleher STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF DEFENSE CHECKED BY Charles E. Besore DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil APPROVED BY Michael A. Frye DRAWING APPROVAL DATE 87-12-30 MICROCIRCUIT, LINEAR, 5-VOLT POSITIVE REGULATOR, MONOLITHIC SILICON AMSC N/A REVISION LEVEL B SIZE A SHEET CAGE CODE 67268 1 OF 9 5962-87775 DSCC FORM 2233 APR 97 5962-E272-04 www.DataSheet4U.com 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87775 01 Y X Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3) 1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows: Device type 01 02 Generic number LM123K LT123AK Circuit function 5-volt positive regulator 5-volt positive regulator 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Y Descriptive designator See figure 1 Terminals 2 Package style TO-3 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Input voltage (VIN) ..................................................................... Storage temperature range ..................................................... Maximum power dissipation (PD) ............................................... Lead temperature (soldering, 10 seconds) ............................... Thermal resistance, junction-to-case (θJC) ................................ Maximum output current (IMAX) ................................................ 1.4 Recommended operating conditions. 20 V dc -65°C to +150°C Internally limited +300°C 3°C/W 1/ 3.0 A Ambient operating temperature range (TA)........................... -55°C to +125°C 1/ Without a heat sink, the thermal resistance of the TO-3 package is about 35°C/W. With a heat sink, the effective thermal resistance can only approach the value of 2°C/W, depending on the efficiency of the heat sink. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 SIZE A REVISION LEVEL 5962-87775 SHEET B 2 www.DataSheet4U.com 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 MIL-STD-1835 Test Method Standard Microcircuits. Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 MIL-HDBK-780 List of Standard Microcircuit Drawings. Standard Microcircuit Drawings. (Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for nonJAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MILPRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MILPRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and p.


LC74982W 596287775 5962-87775


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)