Microcircuit Drawing. 5962-87775 Datasheet

5962-87775 Drawing. Datasheet pdf. Equivalent


ETC 5962-87775
www.DataSheet4U.com
REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
A Add device type 02. Technical changes to table 1. Editorial changes
throughout.
B Drawing updated to reflect current requirements. - gt.
81-09-30
04-06-18
APPROVED
N.A. Hauck
R. Monnin
REV
SHEET
REV
SHEET
REV STATUS
OF SHEETS
PMIC N/A
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
REV
B
SHEET
1
PREPARED BY
Marcia B. Kelleher
B
2
CHECKED BY
Charles E. Besore
APPROVED BY
Michael A. Frye
DRAWING APPROVAL DATE
87-12-30
BBBBBBB
3456789
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
MICROCIRCUIT, LINEAR, 5-VOLT POSITIVE
REGULATOR, MONOLITHIC SILICON
AMSC N/A
DSCC FORM 2233
APR 97
REVISION LEVEL
B
SIZE
A
SHEET
CAGE CODE
67268
1 OF 9
5962-87775
5962-E272-04


5962-87775 Datasheet
Recommendation 5962-87775 Datasheet
Part 5962-87775
Description Standard Microcircuit Drawing
Feature 5962-87775; www.DataSheet4U.com REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add device type 02. Tech.
Manufacture ETC
Datasheet
Download 5962-87775 Datasheet




ETC 5962-87775
www.DataSheet4U.com
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-87775
01
Y
X
Drawing number
Device type
(see 1.2.1)
Case outline
(see 1.2.2)
Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) shall identify the circuit function as follows:
Device type
Generic number
Circuit function
01
LM123K
5-volt positive regulator
02
LT123AK
5-volt positive regulator
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
Descriptive designator
Terminals
Package style
Y
See figure 1
2
TO-3
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Input voltage (VIN) ..................................................................... 20 V dc
Storage temperature range ..................................................... -65°C to +150°C
Maximum power dissipation (PD) ............................................... Internally limited
Lead temperature (soldering, 10 seconds) ............................... +300°C
Thermal resistance, junction-to-case (θJC) ................................ 3°C/W 1/
Maximum output current (IMAX) ................................................ 3.0 A
1.4 Recommended operating conditions.
Ambient operating temperature range (TA)........................... -55°C to +125°C
1/ Without a heat sink, the thermal resistance of the TO-3 package is about 35°C/W. With a heat sink, the effective
thermal resistance can only approach the value of 2°C/W, depending on the efficiency of the heat sink.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
B
5962-87775
SHEET
2



ETC 5962-87775
www.DataSheet4U.com
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or www.dodssp.daps.mil or
from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as
specified in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.2 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
A
REVISION LEVEL
B
5962-87775
SHEET
3





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)