|
|
Controlled Oscillators. CX032 Datasheet |
|
|
|
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
www.conwin.com
PRODUCT DATA
CRYSTAL CONTROLLED OSCILLATORS
SHEET
SURFACE MOUNT 3.3V HCMOS STRATUM 3 OCXO
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Storage Temperature
www.DataSheet4SUup.pclyoVmoltage
Control Voltage
OPERATING SPECIFICATIONS
PARAMETER
Center Frequency
Frequency Calibration, Vc=1.59 Vdc
Frequency Stability
Aging (Daily)
Aging (20 Years)
Total Frequency Tolerance
Operating Temperature Range
Supply Voltage
Supply Current
Phase Jitter (BW=12KHz to 20MHz)
Phase Jitter (BW=10Hz to 20MHz)
Period Jitter
SSB Phase Noise at 10Hz offset
SSB Phase Noise at 10KHz offset
Warm Up Time
TDEV @ 1.0 Sec.
TDEV @ 4.0 Sec.
INTPUT CHARACTERISTICS
PARAMETER
Control Voltage Range
Frequency at Vc=0.3 Vdc
Frequency at Vc=3.0 Vdc
Slope of Frequency Adjust
Input Impedance
UNITS
(Vcc)
(Vc)
MINIMUM
-40
-0.5
-0.5
NOMINAL
-
-
-
MAXIMUM
85
4.5
4.5
UNITS
°C
Vdc
Vdc
TABLE 1.0
NOTE
(Fo)
(Vcc)
(Icc)
MINIMUM
1.544
-1.5
-0.25
-30
-2.5
-4.6
0
3.135
-
-
-
-
-
-
-
-
-
NOMINAL
-
-
-
-
-
-
3.3
-
-
-
-
-90
-135
-
-
-
MAXIMUM
20.0
1.5
0.25
30
2.5
4.6
70
3.465
450
1
3
5
-
-
5
1
2
UNITS
MHz
ppm
ppm
ppb
ppm
ppm
°C
Vdc
mA
ps rms
ps rms
ps rms
dBc/Hz
dBc/Hz
Minutes
nS
nS
TABLE 2.0
NOTE
1
2
3
4
5
TABLE 3.0
MINIMUM NOMINAL MAXIMUM UNITS
NOTE
(Vc) 0.3 1.59 3.0 Vdc
-38
-
-25 ppm
6
25
-
38 ppm
6
18.5 -
- ppm/V
100k
-
- Ohm
HCMOS OUTPUT CHARACTERISTICS
PARAMETER
LOAD
Voltage
(High)
(Low)
Current
(High)
(Low)
Duty Cycle at 50% of Vcc
Rise / Fall Time 10% to 90%
PACKAGE CHARACTERISTICS
Package
PROCESS RECOMMENDATIONS
Solder Reflow
Wash
(Voh)
(Vol)
(Ioh)
(Ioh)
MINIMUM
-
2.6
-
-4
-
45
-
NOMINAL
-
-
-
-
50
-
MAXIMUM
15
-
0.4
-
4
55
6
UNITS
pf
Vdc
Vdc
mA
mA
%
nS
TABLE 4.0
NOTE
TABLE 5.0
Surface Mount, Non-hermetic package consisting of a n FR4 substrate with
grounded metal cover.
TABLE 6.0
The component solder used internal to this device has a m elting point of
221°C. The peak temperature inside the device should be less than or equal
to 220°C for a maximum of 10 seconds
Ultrasonic cleaning is not recommended
Notes:
1)
2)
3)
4)
5)
6)
Initial calibration @ 25°C, Vc=1.59 Vdc.
Frequency vs. temperature stability
At the time of shipment after48 hours of operation.
Inclusive of calibration, operating temperature range, supply voltage change, load change, shock
and vibration, 20 years aging.
Measured @ 25°C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency,
measured after 30 minutes of contin uous operation at a stable 25°C
Referenced to Fo @ 25°C, Positive Transfer Characteristic
DATASHEET #: Cx032 PAGE 1 OF 2
REV: 03
DATE: 11/12/04
BSOV3S3
DESCRIPTION
The Connor-Winfield
BSOV3S3 is a true Surface
Mount 3.3V, Voltage
Controlled Oven Controlled
Crystal Oscillator (VCOCXO)
with an HCMOS output. The
BSOV3S3 is designed for
Stratum 3 applications
requiring high pullability, tight
frequency stability and low
jitter.
FEATURES
FREQUENCY ADJUST
3.3V OPERATION
LOW JITTER <1pS RMS
TEMPERATURE STABILITY
±0.25ppm
FREQUENCY TOLERANCE OF
±4.6ppm OVER TEN YEARS
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
ORDERING INFORMATION
BSOV3S3 - 12.80MHz
OCXO
SERIES
CENTER
FREQUENCY
Specifications subject to change without notice.
aCopyright 2001 Connor-Winfield all rights reserved.
|
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
www.conwin.com
PRODUCT DATA
CRYSTAL CONTROLLED OSCILLATORS
SHEET
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1m inute
transition.
SOLDERING
Pad Solderability: Per MIL-STD-883, Method 2003. 8 hour steam age prior to 245°C ±5°C Solder pot dip, 95%
Coverage.
Solder Reflow: The component solder internal to this device has a melt ing point of 221°C, the peak temperature inside t he
device should be less than or equal to 220°C for a maximum of 10 seconds.
www.DataSheet4U.com
MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15mi nute cycles 12 times each
perpendicular axis.
Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, half sine, 3 shocks per direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C.
.330 max
(8.382mm)
PIN FUNCTION
1 CONTROL VOLTAGE
7 GROUND (CASE)
8 OUTPUT
14 Vcc
Dimensional Tolerance:
±.005 (.127mm)
KEEP OUT AREA
90%
50%
10%
.830
(21.08mm)
.565
(14.35mm)
CONTROL
VOLTAGE
3.0Vdc
POWER
SUPPLY
3.3Vdc
14 8
17
DATASHEET #: Cx032
PAGE 2 OF 2
REV: 03
DATE: 11/12/04
Specifications subject to change without notice.
aCopyright 2001 Connor-Winfield all rights reserved.
|
| @ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact) |