Document
TLGE18CP(F)
TOSHIBA InGaAℓP LED
TLGE18CP(F)
○ Panel Circuit Indicator
• • • • • Lead(Pb)-free products (lead: Sn-Ag-Cu) 5 mm package wide viewing angle InGaAℓP Emitted color: green Colored, Transparent lens amusement equipment illumination sources. and panel backlighting Unit: mm
• Applications: Various types of information panels, indicators for www.DataSheet4U.com
•
Stopper lead type is also available. TLGE18C(F)
Lineup
Product Name TLGE18CP(F) Color Green Material
InGaA lP
JEDEC JEITA TOSHIBA
― ― 4-5AN2
Absolute Maximum Ratings (Ta = 25°C)
Product Name TLGE18CP(F) Forward Current IF (mA) 50 Reverse Voltage VR (V) 4 Power Dissipation PD (mW) 120
Weight: 0.31 g(Typ.)
Operating Temperature Topr (°C) −40~100 Storage Temperature Tstg (°C) −40~120
Electrical and Optical Characteristics (Ta = 25°C)
Product Name Min TLGE18CP(F) Unit 565 Emission Wavelength
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc).
Reverse Current IR IF 20 mA Max 50 μA VR 4 V
Luminous Intensity IV Δλ Typ 20 IF 20 mA Min 153 Typ 500 mcd IF 20
Forward Voltage VF Typ 2.0 V Max 2.4
λd
Typ 571 Max 576 nm
λP Typ 574
Note:
Precautions
• •
Lamps are classified into the following ranks according to their luminous intensity. Each packing box includes single Luminous Intensity class. IV 、P:153-414mcd, Q: 272-736mcd,R:476mcd -、λd、1: 565-573nm, 2: 569-576nm
Please be careful of the following: Soldering temperature: 260°C max, soldering time: 3 s max (soldering portion of lead: up to 1.6 mm from the body of the device)
If the lead is formed, the lead should be formed up to 1.6 mm from the body of the device without forming stress to the resin. Soldering should be performed after lead forming. • This visible LED lamp also emits some IR light. If a photo detector is located near the LED lamp, please ensure that it will not be affected by this IR light
1
2007-10-01
TLGE18CP(F)
TLGE18CP(F)
IF – V F
100 Ta = 25°C 5000 Ta = 25°C
IV – IF
30
Luminous intensity IV (mcd)
1.7 1.8 1.9 2.0 2.1 2.2
50
(mA)
1000
Forward current IF
10
5 3
100
www.DataSheet4U.com
1 1.6 2.3 10 1 3 5 10 30 50 100
Forward voltage VF
(V)
Forward current IF
(mA)
IV – Tc
10 1.0
Relative luminous intensity – Wavelength
IF = 20 mA Ta = 25°C
Relative luminous intensity IV
5 3
Relative luminous intensity
−20 0 20 40 60
0.8
0.6
1 0.5 0.3
0.4
0.2
0.1
80
0 520
540
560
580
600
620
640
Case temperature Tc (°C)
Wavelength λ (nm)
Radiation pattern
80
IF – Ta Ta = 25°C
IF (mA)
60
30° 40° 50° 60° 70° 80° 90°
20°
10°
0°
10°
20°
30° 40° 50° 60° 70° 80° 90° 1.0
Allowable forward current
40
20
0
0.2
0.4
0.6
0.8
0 0
20
40
60
80
100
120
Ambient temperature Ta (°C)
2
2007-10-01
TLGE18CP(F)
www.DataSheet4U.com
RESTRICTIONS ON PRODUCT USE
• The information contained herein is subject to change without notice.
20070701-EN
• TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety dev.