RADIAL. CC75xxxx Datasheet

CC75xxxx RADIAL. Datasheet pdf. Equivalent


Kemet Corporation CC75xxxx
CERAMIC MOLDED AXIAL & RADIAL
PERFORMANCE CHARACTERISTICS
GENERAL
Working Voltage:
C0G – 50, 100 & 200 Volts
X7R – 50, 100 & 200 Volts
Temperature Characteristics:
C0G – 0 ±30 PPM/°C from -55°C to +125°C
X7R – ±15% from -55°C to +125°C
Capacitance Tolerance:
C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%
(±0.5 pF is tightest available tolerance)
X7R – ±10%, ±20%, -0 +100%, -20% +80%
Construction:
www.DataSheMeot4nUo.cliothmic block of ceramic dielectric with interdigitated
internal electrodes, encapsulated in a molded case, and
having axial or radial leads. Meets flame test requirements
of UL Standard 94V-0.
Terminal Strength:
EIA-198 Method 303 Condition A (2.2 kg)
ELECTRICAL
Capacitance:
Within specified tolerance when measured with 1 volt rms
at 1 kHz (1000 pF or less at 1 MHz for C0G).
Dissipation Factor:
25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).
C0G – .15% maximum
X7R – 2.5% maximum
Insulation Resistance:
After 2 minutes electrification at 25°C and rated voltage
C0G – 100K megohms or 1000 megohm - µF, whichever
is less.
X7R – 100K megohms or 1000 megohm - µF, whichever
is less.
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current limited
to 50 mA at 25°C.
Life Test:
2000 hours at 200% of rated voltage at 125°C. Post-Test
limits at 25°C are:
Capacitance Change:
C0G – less than 3% or 0.25 pF, whichever is higher
X7R – ±20% of initial value
Dissipation Factor:
C0G – .25% maximum
X7R – 3.0% maximum
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current
limited to 50 mA.
ENVIRONMENTAL
Moisture Resistance:
MIL-STD-202, Method 106, or EIA-198, Method 204,
Condition A, except 20 cycles.
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Dielectric Withstanding Voltage:
250% of rated voltage for 5 seconds with current
limited to 50 mA.
Immersion Cycling:
MIL-STD-202, Method 104, Condition B. Post-Test limits
at 25°C are:
Insulation Resistance:
C0G – 10K megohms or 100 megohm - µF, whichever
is less
X7R – 10K megohms or 100 megohm - µF, whichever
is less
Solderability:
MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2
seconds.
Resistance to Soldering Heat:
MIL-STD-202, Method 210, Condition B (260°C, 10 secs).
Depth of immersion — to a minimum of .050" from the
capacitor body.
Lead Material:
Axial: Solder-coated copper clad steel
Radial: Solder-coated copper
20 © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300


CC75xxxx Datasheet
Recommendation CC75xxxx Datasheet
Part CC75xxxx
Description CERAMIC MOLDED AXIAL & RADIAL
Feature CC75xxxx; CERAMIC MOLDED AXIAL & RADIAL PERFORMANCE CHARACTERISTICS GENERAL Working Voltage: C0G – 50, 100 & 2.
Manufacture Kemet Corporation
Datasheet
Download CC75xxxx Datasheet




Kemet Corporation CC75xxxx
CERAMIC MOLDED/AXIAL & RADIAL — MIL-PRF-20
CAPACITOR OUTLINE DRAWINGS (AXIAL LEADS)
1.50 Min. L 1.50 Min.
(38.10)
(38.10)
D
C
www.DataSheet4U.com
CASE
SIZE
C114
C124
C192
C202
C222
DIMENSIONS — INCHES & (MILLIMETERS)
MILITARY
EQUIVALENT STYLES
CC75, CCR75
L
.160 ± .010 (4.06 ± .25)
D
.090 ± .010 (2.29 ± .25)
C
.020, +.000, -.003 (.51, +.00, -.08)
CC76, CCR76
.250 ± .010 (6.35 ± .25)
.090 ± .010 (2.29 ± .25)
.020, +.000, -.003 (.51, +.00, -.08)
CC77, CCR77
.390 ± .010 (9.91 ± .25)
.140 ± .010 (3.56 ± .25)
.025, +.002, -.002 (.64, +.05, -.05)
CC78, CCR78
.500 ± .020 (12.70 ± .51)
.250 ± .015 (6.35 ± .38)
.025, +.002, -.002 (.64, +.05, -.05)
CC79, CCR79
.690 ± .030 (17.53 ± .76)
.350 ± .020 (8.89 ± .51)
.025, +.002, -.002 (.64, +.05, -.05)
CAPACITOR OUTLINE DRAWINGS (RADIAL LEADS)
C052 (CC05, CCR05)
LW
C056 (CCR05)
LW
C062 (CC06, CCR06), C512 (CC07, CCR07),
C522 (CC08, CCR08)
LW
C066 (CCR06)
LW
HH
H
1.25
MIN.
Lead Dia.
.025
(+.004
-.002)
S
.045
MAX.
1.25
MIN.
Lead Dia.
.025
(+.004
-.002)
.026
MIN.
1.25
MIN.
Lead Dia.
.025
(+.004
-.002)
SS
Center Line of leads within .030" of Center Line of case.
* Leads are .625 minimum when tape and reel packaged
.026
H MIN.
Lead Dia.
1.25 .025
MIN. (+.004
-.002)
S
DIMENSIONS — INCHES & (MILLIMETERS)
CASE
SIZE
C052/
C056
C062/
C066
C512
C522
MILITARY
EQUIVALENT
STYLES
CC05, CCR05
CC06, CCR06
CC07, CCR07
CC08, CCR08
H
HEIGHT
.190 ± .010 (4.83 ± .25)
.290 ± .010 (7.37 ± .25)
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
L
LENGTH
.190 ± .010 (4.83 ± .25)
.290 ± .010 (7.37 ± .25)
.480 ± .020 (12.19 ± .51)
.480 ± .020 (12.19 ± .51)
W
WIDTH
.090 ± .010 (2.29 ± .25)
.090 ± .010 (2.29 ± .25)
.140 ± .010 (3.56 ± .25)*
.240 ± .010 (6.10 ± .25)
* 0.200 (5.08) maximum for 100,000 pF only.
S
LEAD
SPACING
.200 ± .015 (5.08 ± .38)
.200 ± .015 (5.08 ± .38)
.400 ± .020 (10.16 ± .51)
.400 ± .020 (10.16 ± .51)
For packaging information, see pages 39, 40, and 41.
© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300
27



Kemet Corporation CC75xxxx
CERAMIC MOLDED/AXIAL & RADIAL — MIL-PRF-20
ORDERING INFORMATION
C 052 G 102 J 1 G 5 C R**
CERAMIC
FAILURE RATE
*CASE SIZE
(See Table Below)
A Not Applicable (Std.)
M 1.0%
P 0.1%
SPECIFICATION
Military
R 0.01%
S 0.001%
G MIL-PRF-20
CAPACITANCE
In picofarad code: First two digits are significant
LEAD MATERIAL
C Standard
figures and third is number of zeroes following
(except 9 indicates division by 10). Examples:
www.DataShe0e.t14U.Fco=m100,000 pF = 104 and 9.1 pF = 919.
See tables for Standard Values.
INTERNAL CONSTRUCTION
CAPACITANCE TOLERANCE
5 Standard
Standard
K ±10%
J ±5%
Others
G ±2% C ±0.25 pF
F ±1% D ±0.5 pF
B ±0.1 pF
WORKING
VOLTAGE
1 100
2 200
5 50
Standard tolerances for each Series are
shown in the repetitive parts lists.
*CASE SIZES
RADIAL
AXIAL
TEMPERATURE CHARACTERISTIC
KEMET Military
Designator Equivalent
EIA
Equivalent
Capacitance Change With Temp.
Temp.
Range, °C
Measured
Without
DC Bias
Voltage
Measured
With Bias
(Rated
Voltage)
G *CG C0G
(Ultra (See below) (NPO)
Stable)
-55 to
+125
±30 ±30
ppm/°C* ppm/°C*
C052
C114
C056
C062
C066
C512
C124
C192
C202
C222
*CH ±60 ppm/°C 8.2 pF-18.0 pF.
*CJ ±120 ppm/°C 4.3 pF-7.5 pF.
*CK ±250 ppm/°C 2.2 pF-3.9 pF
*CX not measurable 0.1 pF-2.0 pF.
C522 **Part Number Example: C052G102J1G5CR (14 digits – no spaces)
JCK
2R2
CM5
11AK
CCR77C
G102JM
J31433
0504A
CCR78CG
103FR
JAN K
31433
100V
0504A
CCR79CG
103KM
JAN K
31433
200V
0504A
CAPACITOR MARKING
CC(R) 75, 76
JBrand (CCR only), Temperature Characteristic
Capacitance
Capacitance Tolerance, Failure Rate (CCR only),
Year Code
Lot Code, Trademark (K)
CC(R) 77
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
JBrand (CCR only), FSCM (Federal Source Code)
Date/Lot Code
CC(R) 78
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
JANBrand (CCR only), Trademark (K)
FSCM (Federal Source Code)
Voltage
Date/Lot Code
FRONT
CCR0
5CH1
00FR
REAR
0504
AJ3
1433
FRONT
CCR06
CG102
JS
REAR
0504A
J100V
31433
CC(R) 05
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
** For the standoff style, a Vis added after the
failure rate, or last character.
Date Code
Lot Code, JBrand (CCR only),
FSCM (Federal Source Code)
CC(R) 06
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
** For the standoff style, a Vis added after the
failure rate, or last character.
Date/LotCode
JBrand (CCR only), Voltage
FSCM (Federal Source Code)
CC(R) 07
CC(R) 79
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
JANBrand (CCR only), Trademark
FSCM (Federal Source Code)
Voltage
Date/Lot Code
CCR07CG
472KM
JAN KEMET
31433
200V 0504A
CCR08CG
472KM
JAN KEMET
31433
200V 0509A
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
JANBrand, Trademark
FSCM (Federal Source Code)
Voltage, Date/Lot Code
CC(R) 08
Military Designation (Type, Temperature Characteristic,
Capacitance, Tolerance, Failure Rate)
JANBrand, Trademark
FSCM (Federal Source Code)
Voltage, Date/Lot Code
28 © KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, (864) 963-6300







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)