DatasheetsPDF.com

DS1810 Dataheets PDF



Part Number DS1810
Manufacturers Dallas Semiconductor
Logo Dallas Semiconductor
Description 5V EconoReset
Datasheet DS1810 DatasheetDS1810 Datasheet (PDF)

www.maxim-ic.com DS1810 5V EconoReset with Push-Pull Output FEATURES § Automatically restarts a microprocessor after power failure § Maintains reset for 150 ms after VCC returns to an in-tolerance condition § Reduces need for discrete components § Precision temperature-compensated voltage reference and voltage sensor § Low-cost TO-92 or space saving surface mount SOT-23 packages available § Push-Pull output for low current operation § Operating temperature -40°C to +85°C PIN ASSIGNMENT DALLA.

  DS1810   DS1810



Document
www.maxim-ic.com DS1810 5V EconoReset with Push-Pull Output FEATURES § Automatically restarts a microprocessor after power failure § Maintains reset for 150 ms after VCC returns to an in-tolerance condition § Reduces need for discrete components § Precision temperature-compensated voltage reference and voltage sensor § Low-cost TO-92 or space saving surface mount SOT-23 packages available § Push-Pull output for low current operation § Operating temperature -40°C to +85°C PIN ASSIGNMENT DALLAS DS1810 Econo Reset 3 123 123 BOTTOM VIEW TO-92 PACKAGE See Mech. Drawings Section On Website 12 TOP VIEW SOT-23 PACKAGE See Mech. Drawings Section On Website PIN DESCRIPTION TO-92 1 RST 2 VCC 3 GND Active Low Reset Output Power Supply Ground SOT-23 1 RST 2 VCC 3 GND Active Low Reset Output Power Supply Ground DESCRIPTION The DS1810 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to an in-tolerance condition, the reset signal is kept in the active state for approximately 150 ms to allow the power supply and processor to stabilize. 1 of 5 041002 DS1810 OPERATION - POWER MONITOR The DS1810 provides the function of detecting out-of-tolerance power supply conditions and warning a processor-based system of impending power failure. When VCC is detected as out-of-tolerance, the RST signal is asserted. On power-up, RST is kept active for approximately 150 ms after the power supply has reached the selected tolerance. This allows the power supply and microprocessor to stabilize before RST is released. BLOCK DIAGRAM (PUSH-PULL OUTPUT) Figure 1 APPLICATION EXAMPLE Figure 2 OUTPUT VALID CONDITIONS All versions of the DS1810 can maintain a valid output as long as VCC remains above 1.2 volt. However, the RST outputs on the DS1810 use a push-pull structure which can maintain a valid output below 1.2 volts on an input. To sink current below 1.2 volts, a resistor can be connected from RST to Ground (see Figure 3). This arrangement will maintain a valid value on the RST outputs even it VCC approaches 0 volts. During both power-up and -down this arrangement will draw current when RST is in the high state. A value of about 100 kV should be adequate to maintain a valid condition. 2 of 5 APPLICATION DIAGRAM: RST VALID TO 0 VOLTS VCC ON THE DS1810 Figure 3 TIMING DIAGRAM: POWER-UP Figure 4 DS1810 TIMING DIAGRAM: POWER-DOWN Figure 5 3 of 5 ABSOLUTE MAXIMUM RATINGS* Voltage on VCC Pin Relative to Ground Voltage on RST Relative to Ground Operating Temperature Storage Temperature Soldering Temperature -0.5V to +7.0V -0.5V to VCC +0.5V -40°C to +85°C -55°C to +125°C 260°C for 10 seconds DS1810 * This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. RECOMMENDED DC OPERATING CONDITIONS PARAMETER SYMBOL MIN TYP Supply Voltage VCC 1.2 (-40°C to +85°C) MAX UNITS NOTES 5.5 V 1 DC ELECTRICAL CHARACTERISTICS (-40°C to +85°C; VCC=1.2V to 5.5V) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES Output Voltage @ 0-500 mA VOH VCC-0.5V VCC-0.1V V1 Output Current @ 2.4V IOH 350 mA 2 Output Current @ 0.4V IOL +10 mA 2 Operating Current VCC < 5.5 ICC 30 40 mA 3 VCC Trip Point (DS1810-5) VCCTP 4.50 4.62 4.75 V 1 VCC Trip Point (DS1810-10) VCCTP 4.25 4.37 4.49 V 1 VCC Trip Point (DS1810-15) VCCTP 4.00 4.12 4.24 V 1 Output Capacitance COUT 10 pF AC ELECTRICAL CHARACTERISTICS (-40°C to +85°C; VCC=1.2V to 5.5V) PARAMETER SYMBOL MIN TYP MAX UNITS NOTES RESET Active Time VCC Detect to RST tRST 100 150 300 ms tRPD 2 5 ms VCC Slew Rate tF 300 ms (VCCTP (MAX) to VCCTP (MIN)) VCC Slew Rate tR 0 ns (VCCTP (MIN) to VCCTP (MAX)) VCC Detect to RST tRPU 100 150 300 ms 4 4 of 5 NOTES: 1. All voltages are referenced to ground. 2. Measured with VCC ³ 2.7 volts. 3. Measured with RST output open. 4. tR = 5 ms. PART MARKING CODES DS1810 SOT-23 PACKAGE “A”, “B”, &“C” represent the device type. 810 - DS1810 811 - DS1811 812 - DS1812 813 - DS1813 815 - DS1815 816 - DS1816 817 - DS1817 818 - DS1818 “D” represents the device tolerance. A- 5% B- 10% C- 15% D- 20% 5 of 5 .


PJA733 DS1810 DS1811


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)