DatasheetsPDF.com

LA7848 Dataheets PDF



Part Number LA7848
Manufacturers Sanyo
Logo Sanyo
Description TV Vertical Output + E/W Driver
Datasheet LA7848 DatasheetLA7848 Datasheet (PDF)

Ordering number : ENN7877 www.DataSheet4U.com Monolithic Linear IC LA7848 Overview TV Vertical Output + E/W Driver with Bus Control Support The LA7848 is a vertical deflection plus EW driver IC for high image quality TV and CRT displays that supports the use of a bus control system signal-processing IC. The sawtooth waveform from the bus control system signal-processing IC can directly drive the deflection yoke (including the DC component). The LA7848 also provides a parabolic waveform outp.

  LA7848   LA7848


Document
Ordering number : ENN7877 www.DataSheet4U.com Monolithic Linear IC LA7848 Overview TV Vertical Output + E/W Driver with Bus Control Support The LA7848 is a vertical deflection plus EW driver IC for high image quality TV and CRT displays that supports the use of a bus control system signal-processing IC. The sawtooth waveform from the bus control system signal-processing IC can directly drive the deflection yoke (including the DC component). The LA7848 also provides a parabolic waveform output that can similarly be used to drive the diode modulator block. Functions • Built-in pump-up circuit for low power dissipation. • Vertical output circuit. • Excellent crossover characteristics. Specifications Maximum Ratings at Ta = 25°C Parameter Supply voltage Output block supply voltage Allowable power dissipation Deflection output current EW drive current *1 EW drive voltage *2 Thermal resistance Operating temperature Storage temperature Symbol +B6 max +B3 max Pd max I2 max I10 max V10 max θj-c Topr Tstg V10 = 1.5V I10 = 10µA Mounted on an arbitrarily large heat sink. Conditions Ratings 45 92 9 -1.5 to +1.5 +0.5 45 4 -20 to +85 -40 to +150 Unit V V W Ap-o Ap-o V °C /W °C °C Note: The EW driver is used within the range that connects the two points *1 and *2. 90705 MS OT B8-5526 No.7877-1/6 LA7848 Operating Conditions at Ta = 25°C Parameter Recommended supply voltage www.DataSheet4U.com Operating supply voltage range Deflection output current EW drive current +B6 +B6op I2p-p I10 Symbol Conditions Ratings 30 16 to 43 To 2.2 To 0.4 Unit V V Ap-p Ap-o Operating Characteristics at Ta = 25°C, +B = 30V Ratings Parameter Deflection output saturation voltage (lower) Deflection output saturation voltage (upper) Pump-up charge saturation voltage Pump-up discharge saturation voltage Idling current Midpoint voltage EW drive saturation voltage Idl Vmid Vsat10-1 I10 = 500mA 15 14.0 15.0 Vsat6-7 I7 = -1.1A Vsat7-1 I7 = 20mA Vsat3-2 I2 = -1.1A Symbol Vsat2-1 I2 = 1.1A Conditions min typ max 1.5 3.2 1.8 3.2 50 16.0 1.5 V V V V mA V V Unit Note: Current flowing into the IC is positive (+) and current flowing out is negative (-). Package Dimensions unit : mm 3248A No.7877-2/6 LA7848 Block Diagram www.DataSheet4U.com Test Circuit Diagrams 1. Output saturation voltage (lower) Vsat2-1 Figure 1 In the circuit in figure 1, read the value shown by the voltage meter (V) when the current meter (A) reads 1.1A. No.7877-3/6 LA7848 2. Output saturation voltage (upper) Vsat3-2 Figure 2 www.DataSheet4U.com In the circuit in figure 2 with the output from pin 2 absorbed by an electronic load and read the value shown by the voltage meter (V) when the current meter (A) reads 1.1A. 3. Charge pump charge saturation voltage Vsat7-1 Figure 3 In the circuit in figure 3, read the value shown by the voltage meter (V) when the current meter (A) reads 20mA. No.7877-4/6 LA7848 4. Charge pump discharge saturation voltage Vsat6-7 Figure 4 www.DataSheet4U.com In the circuit in figure 4 with the output from pin 7 absorbed by an electronic load, read the value shown by the voltage meter (V) when the current meter (A) reads 1.1A. 7. Idling current Idl 8. Midpoint voltage Vmid Figure 5 In the circuit in figure 5, read the value shown by the current meter (A). In the circuit in figure 5, read the value shown by the voltage meter (V). No.7877-5/6 LA7848 9. EW drive saturation voltage Vsat10-1 Figure 6 www.DataSheet4U.com In the circuit in figure 6, read the value shown by the voltage meter (V) when the current meter (A) reads 500mA. ! Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. ! SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. ! In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities conce.


AN541 LA7848 KTIR0221DS


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)