DatasheetsPDF.com

NJU6050 Dataheets PDF



Part Number NJU6050
Manufacturers JRC
Logo JRC
Description High Efficiency White LED Driver
Datasheet NJU6050 DatasheetNJU6050 Datasheet (PDF)

NJU6050 www.DataSheet4U.com High Efficiency White LED Driver ¢ GENERAL DESCRIPTION The NJU6050 is a high-efficiency white LED driver. It contains a high-efficiency step-up DC/DC converter and an output driver. The IC can output max.28V and drive as many as 8 white LEDs in series with a constant current, which guarantees the LEDs with uniform brightness. The high frequency of the step-up converter permits the use of small, low-profile inductors and capacitors to minimize the footprint in space-c.

  NJU6050   NJU6050


Document
NJU6050 www.DataSheet4U.com High Efficiency White LED Driver ¢ GENERAL DESCRIPTION The NJU6050 is a high-efficiency white LED driver. It contains a high-efficiency step-up DC/DC converter and an output driver. The IC can output max.28V and drive as many as 8 white LEDs in series with a constant current, which guarantees the LEDs with uniform brightness. The high frequency of the step-up converter permits the use of small, low-profile inductors and capacitors to minimize the footprint in space-conscious applications. The NJU6050also features low operating voltage of 2.5V and the small package SOT-23 (MTP-5). All of these benefits make the NJU6050 suitable for the battery-powered portable applications such as cellular phones, camcorders, PDAs, etc. ¢ PACKAGE OUTLINE ¢ FEATURES ˜ Drives Up to 8 White LEDs in Series ˜ ˜ ˜ ˜ VSW = 28V, IOUT = 20mA Uses Small Inductor and Capacitors 2.5V to 6.5V Operating Voltage for Step-up Circuits (VDD ) CMOS Technology Package : SOT-23 5 pin (MTP-5) ¢ PIN CONFIGURATION (TOP VIEW) SW VSS FB 1 2 3 5 VDD 4 SHDNb Ver.2006-03-28 -1- NJU6050 www.DataSheet4U.com ¢ PIN DESCRIPTIONS No. 1 2 3 4 5 SYMBOL SW VSS FB SHDNb VDD TYPE Input Power Input Input Power Switch Terminal Ground Terminal Feedback Terminal Shutdown Terminal Active “L” “L” : Shutdown “H” : Normal Operation Power Supply terminal DESCRIPTION ¢ BLOCK DIAGRAM L1 VIN C1 Bias DC/DC Control + VREF 1.2V RLED VSS VIN ILED VDD SW FB D2 C2 D1 VOUT SHDNb Shutdown circuit ¢ FUNCTIONAL DESCRIPTONS (1) LED Current Control and Resistor R LED Selection The NJU6050 incorporates the LED current control to regulate the LED current (ILED), which is programmed by the feedback resistor (RLED) connected between the FB and the VSS terminals. The reference voltage VREF is internally regulated to 1.2V typical and connected to the positive input of the built-in comparator. Formula (1) is used to choose the value of the RLED , as shown below. RLED = VREF I LED --- Formula (1) VREF =1.2V (typ.) The ILED is the constant current programmed by the RLED . When the feedback voltage on the FB terminal reaches above the reference voltage VREF (i.e., ILED is above the level programmed by RLED ), the output capacitor C2 delivers the ILED . Once the feedback voltage drops below the reference voltage (i.e., ILED drops below the level programmed by the RLED ), the MOS switch is turned on, then the current of the inductor L1 begins increasing. When the switch current reaches 350mA, the MOS switch is turned off, then the L1 delivers current to the output through the diode D1 as the inductor current drops. After that, the MOS switch is turned on again and the switch current increases up to 350mA. This switching cycle continues until the ILED reaches the level programmed by the RLED , then the ILED current is maintained constant. -2- Ver.2006-03-28 NJU6050 www.DataSheet4U.com (2) Inductor Selection The following equation gives the optimum inductor value: L = VOUT-VIN(MIN)+VD ICL VD ICL t OFF Formula (2) : Schottky diode Voltage :Switch current limit The power supply voltage VIN may fluctuate in battery-powered applications. For this reason, the minimum voltage should be applied to the VIN in Formula (2). The NJU6050 has about 100ns of delay time (TDELAY ), which is defined as the period from the reach of the current limit 350mA to the MOS-switch-off. The TDELAY may cause an overshoot-inductor-current, which is called the peak current IL,PEAK, and calculated by Formula (3). Therefore, it is recommended that an inductor with a rating twice of the IL,PEAK and a low DCR (DC resistance) be used for high efficiency. IL,PEAK = ICL + VIN(MAX) -VDS L tDELAY Formula (3) VDS VIN(MAX) : Drain-Source voltage of MOS switch (=ILIMIT*RON) : Maximum of VIN Voltage (3) Diode Selection A schottky diode with a low forward-voltage-drop and a fast switching-speed is ideal for the D1. And the D1 must have a rating greater than the output voltage and output current in the system. (4) Capacitor Selection A low ESR (Equivalent Series Resistance) capacitor should be used as the output capacitor C2 to minimize output ripples. A multi-layer ceramic capacitor is the best selection for the NJU6050 application because of not only the low ESR but its small package. A ceramic capacitor is also recommended for the input decoupling-capacitor C1, and should be placed as close to the NJU6050 as possible. (5) Open-circuit Protection The zener diode D2 works as an open-circuit protection. When the LED is disconnected from the circuit, the feedback voltage on the FB terminal is pulled down to 0V, which makes the switching frequency maximum. Without the diode D2, the SW voltage exceeds the absolute maximum rating, and this voltage stress may cause a permanent damage to the IC. The zener voltage must be greater than the maximum forward-voltage of the LED string. Ver.2006-03-28 -3- NJU6050 www.DataSheet4U.com ¢ ABSOLUTE MAXIMUMN RATINGS Ta=25°C PARAMETERS VDD Power Sup.


NJU6049 NJU6050 NJU6048


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)