Document
SPE0511
Single-Line ESD Protection Array
DESCRIPTION The SPE0511 are designed by TVS device that is to protect sensitive electronics from damage or latch-up due to ESD. They are designed for use in applications where board space is at a premium. SPE0511 will protect single line, and may be used on line where the signal polarities swing above and below ground. SPE0511 offer desirable characteristics for board level protection including fast response time, low operating and clamping voltage, and no device degradation. SPE0511 may be used to meet the immunity requirements
of IEC 61000-4-2, level 4. The small SOD-523 package
makes them ideal for use in portable electronics such as cell phones, PDA’s, notebook computers, and digital
cameras.
APPLICATIONS Cellular Handsets and Accessories Cordless Phone PDA Notebooks and Handhelds Portable Instrumentation Digital Cameras MP3 Player
FEATURES Transient protection for data lines to
IEC 61000-4-2 (ESD) ±15kV (air), ±8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) Protects single I/O lines Working voltage: 5V Low leakage current Low operating and clamping voltages
PIN CONFIGURATION ( SOD-523 )
PART MARKING
2020/06/18 Ver.9
Page 1
SPE0511
Single-Line ESD Protection Array
ORDERING INFORMATION
Part Number
Package
SPE0511D52RGB
SOD-523
※ SPE0511D52RGB : Tape Reel ; Pb – Free ; Halogen – Free
Part Marking 1
ABSOULTE MAXIMUM RATINGS (TA=25℃ Unless otherwise noted)
Parameter Peak Pulse Power ( tp = 8/20 μs ) Maximum Peak Pulse Current ( tp = 8/20 μs ) ESD per IEC 61000 – 4 – 2 (Air ) ESD per IEC 61000 – 4 – 2 (Contact ) Operating Junction Temperature Storage Temperature Range Lead Soldering Temperature
Symbol
Typical
Unit
Ppk
250
W
Ipp
7
A
Vpp
±15
KV
Vpp
±8
KV
TJ
-55 ~ 125
℃
TSTG
-55 ~ 150
℃
TL
260 ( 10sec )
℃
ELECTRICAL CHARACTERISTICS (TA=25℃ Unless otherwise noted)
Parameter
Symbol
Conditions
Reverse Stand – Off Voltage Reverse Breakdown Voltage Reverse Leakage Current Reverse Leakage Current Clamping Voltage Clamping Voltage
Junction Capacitance
VRWM VBR IR IR VC VC
Cj
It = 1mA VRWM = 5V , T=25℃ VRWM = 3V , T=25℃
Ipp = 1A , tp = 8/20 μs Ipp = 7A , tp = 8/20 μs Between I/O Pin and GND VR = 0V , f = 1MHz
Min. 6
Typ Max. Unit
5
V
V
0.01
1 μA
0.01 0.5 μA
11 V
15 V
10
20 pF
2020/06/18 Ver.9
Page 2
SPE0511
Single-Line ESD Protection Array
TYPICAL CHARACTERISTICS
Clamping Voltage (Ipp = 1A , tp = 8/20 μs )
2020/06/18 Ver.9
Clamping Voltage (Ipp = 7A , tp = 8/20 μs )
Page 3
SPE0511
Single-Line ESD Protection Array
TYPICAL CHARACTERISTICS
Fig 1 : Junction Capacitance V.S Reverse Voltage Applied Fig 2 : Peak Plus Power V.S Exponential Plus Duration
Fig 3 : Relative Variation of Peal Plus Power V.S Initial Junction Temperature
Fig 4 : Forward Voltage Drop V.S Peak Forward Current
2020/06/18 Ver.9
Page 4
SPE0511
Single-Line ESD Protection Array
Information provided is alleged to be exact and consistent. SYNC Power Corporation presumes no responsibility for the penalties of use of such information or for any violation of patents or other rights of third parties which may result from its use. No license is granted by allegation or otherwise under any patent or patent rights of SYNC Power Corporation. Conditions mentioned in this publication are subject to change without notice. This publication surpasses and replaces all information previously supplied. SYNC Power Corporation products are not authorized for use as critical components in life support devices or systems without express written approval of SYNC Power Corporation.
© The SYNC Power logo is a registered trademark of SYNC Power Corporation © 2020 SYNC Power Corporation – Printed in Taiwan – All Rights Reserved SYNC Power Corporation 7F-2, No.3-1, Park Street NanKang District (NKSP), Taipei, Taiwan, 115, R.O.C Phone: 886-2-2655-8178 Fax: 886-2-2655-8468 © http://www.syncpower.com
2020/06/18 Ver.9
Page 5
.