Power Amplifier
Product Features
• Small size by using simple matching circuit board • Single Supply Voltage • Heat sink 99.9% copper, gold plated • High Productivity • Low Manufacturing Cost • GaAs HFET
RFW0947-10
Application
• GSM Repeater • RF Sub-Systems • Base Station
www.DataSheet4U.com
Package : DP-56
Description
The power amplifier module is designed for base stations and cell extenders and operating frequency range is from 300MHz to 2.3GHz GaAs HFET is used and attached on a copper sub carrier. It is connected by using bias and in/out matching circuit method with gold wire bonding. The bias and matching circuit are designed much simpler than other circuits for silicon IC’s, LDMOS because GaAs HFET is operated by low supply voltage whereas others are operated by high supply voltage. For better thermal conductivity, enhanced mode PCB was used in the 99.9% copper gold plate heat sink. This simplicity results cost competitiveness and performance enhancement.
Specifications
PARAMETER
Frequency Range (MHz) Small Signal Gain (dB) Gain Flatness (Max.) Gain Variation Over Temp Output Return Loss Output P1dB CDMA Power (1 FA) OIP3 @ tone / 27 dBm Noise Figure (Typ.) Drain Voltage Drain Dimensions inCurrent mm Operating Temp Range Dimensions (W×L×H)
NOTE * CDMA : 1.25MHz symbol rate ; Forward Link ; 9 Channels, Multi tone Available @ ±750KHz and ±1.98MHz offset in 30KHz resolution bandwidth * RFW Series : Internally Matched Module
Min
Typ
935 ~ 960 30 ± 0.5dB @ 50MHz BW ± 0.7dB -15dB
Max
± 1.5dB
37 dBm
38 dBm 32dBm @ -45dBc ACPR
50 dBm
51 dBm 4 dB 10V 1.5A Diagram Functional -20°C ~ +70°C 32.0 × 44.0 × 10.0 [mm]
▪ Tel : 82-31-250-5011 ▪
[email protected]
▪ All specifications may change without notice. ▪ Version 1.2
Power Amplifier
RFW0947-10
www.DataSheet4U.com
Performance Charts (Vd=10V, Id=1.5A, T=25℃)
▪ Tel : 82-31-250-5011 ▪
[email protected]
▪ All specifications may change without notice. ▪ Version 1.2
Power Amplifier
Package Dimensions (Type: DP-56)
RFW0947-10
www.DataSheet4U.com
Pin NO 1 2 3
Function GND RF IN E/N
Pin NO 6 5 4
Function Vcc RF OUT GND
Installation Guideline
★ It can be easily removed with solder wick and other removable material
RFHIC Corporation (RFHIC) reserves the right to make changes to any products herein or to discontinue any product at any time without notice. RFHIC do not assume any liability for the suitability of its products for any particular purpose, and disclaims any and all liability, including without limitation consequential or incidental damages. The product specifications herein expressed have been carefully checked and are assumed to be reliable. However, RFHIC disclaims liability for inaccuracies and strongly recommends buyers to verify that the information they are using is current before placing purchase orders. RFHIC products are not intended for use in life support equipment or application where malfunction of the product can be expected to result in personal injury or death. Buyer uses or sells such products for any such unintended or unauthorized application, buyer shall indemnify, protect and hold RFHIC and its directors, officers, stockholders, employees, representatives and distributors harmless against any and all claims arising out of such use. RFHIC’s liability under or arising out of damages, claims of whatsoever kind and nature which RFHIC products could cause shall be limited in amount to the net purchase price of the products sold to buyer by RFHIC.
▪ Tel : 82-31-250-5011 ▪
[email protected]
▪ All specifications may change without notice. ▪ Version 1.2
.