DatasheetsPDF.com

MIC23060 Dataheets PDF



Part Number MIC23060
Manufacturers Micrel Semiconductor
Logo Micrel Semiconductor
Description Sequenced Power Management
Datasheet MIC23060 DatasheetMIC23060 Datasheet (PDF)

MIC23060 Sequenced Power Management IC with HyperLight Load™ DC/DC and Dual Input LDO™ General Description Features The MIC23060 is a highly efficient power management IC integrating a high frequency DC/DC converter with HyperLight Load™ mode and a low input voltage capable LDO. The MIC23060 offers two output voltages at very high efficiency on both outputs while maintaining a low total system cost. The MIC23060 also provides sequencing of the two outputs in every potential combination of tur.

  MIC23060   MIC23060



Document
MIC23060 Sequenced Power Management IC with HyperLight Load™ DC/DC and Dual Input LDO™ General Description Features The MIC23060 is a highly efficient power management IC integrating a high frequency DC/DC converter with HyperLight Load™ mode and a low input voltage capable LDO. The MIC23060 offers two output voltages at very high efficiency on both outputs while maintaining a low total system cost. The MIC23060 also provides sequencing of the two outputs in every potential combination of turn-on and turnoff sequencing by connecting two pins either high or low, and using a single GPIO to enable and disable the device. The LDO is designed both to post regulate from the output of the DC/DC converter for high system efficiency, and/or power directly from the battery. For sequences where the LDO is enabled prior to the DC/DC output, the LDO is first powered by the input voltage (typically the battery source) and then after the DCDC soft start is complete, seamlessly transition LDO input power to draw from the output of the DC/DC converter for higher efficiency operation through post-regulation. The DC/DC converter in the MIC23060 is a HyperLight Load™ converter with very high efficiency at light load and at full operating current, maintaining high efficiency across all operating modes in portable electronics. The MIC23060 is a µCap design, operating with small ceramic output capacitors and tiny inductors for stability, reducing required board space and component cost and is available in the tiny 2.5mm x 2.5mm Thin MLF® package. Data sheets and support documentation can be found on Micrel’s web site at www.micrel.com. • 2.7V to 5.5V supply voltage range • Tiny 12-pin 2.5mm x 2.5mm Thin MLF® package • Integrated sequencing – Dual Input LDO™ can turn-on prior to DC/DC converter and automatically switch to post regulation from the DC/DC converter after it starts – Power for LDO from input during start-up – Adjustable delay time between outputs • Zero-current off mode • Current-limit and thermal shutdown protection HyperLight Load™ DC/DC Converter • Up to 600mA output current in PWM mode (shared between switcher and linear LDO regulator outputs) • 4MHz frequency in continuous PWM mode • Tiny 2.2µH inductor, 4.7µF capacitor • 85% Efficiency at 1mA output current • >90% peak efficiency • Low output voltage ripple across all loads LDO Regulator • Low Input voltage LDO regulator • Stable with ceramic output capacitors • Regulates from the output of the DC/DC converter • 300mA output current capability • High Accuracy: ±3% over temperature • High PSRR: greater than 60dB • Very low quiescent current: 16µA Applications • Mobile phones • PDAs/pocket PCs • Digital cameras/DSP power supply _______________________________________________________________________________________________________________________________________ Typical Application S3 S2 S1 Sequence X 0 0 ALL OFF 0 0 EN DC-DC ON 1st / OFF 1st 0 EN 0 LDO ON 1st / OFF 1st 1 0 EN DC-DC ON 1st /.


MIC2808 MIC23060 S-818


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)