DatasheetsPDF.com

CSTCR4M00G53-B0 Dataheets PDF



Part Number CSTCR4M00G53-B0
Manufacturers Murata Manufacturing
Logo Murata Manufacturing
Description Piezoelectric Ceramic Resonator
Datasheet CSTCR4M00G53-B0 DatasheetCSTCR4M00G53-B0 Datasheet (PDF)

Drawing No. JGC42-4256A www.DataSheet4U.com P. 1/12 Specification of Piezoelectric Ceramic Resonator CSTCR4M00G53-R0 CSTCR4M00G53-B0 Date     Approved by Checked by May 22, 2006   Issued by 1.   Scope は、マイクロコンピュータのクロックにするセラミック (セラロック®)についてします。このにごのにはにへごく ださい。 This product specification is applied to the piezoelectric ceramic resonator used for time base oscillator in a microcomputer. Please contact us when using this product for any other applications than described in the above. 2. .

  CSTCR4M00G53-B0   CSTCR4M00G53-B0


Document
Drawing No. JGC42-4256A www.DataSheet4U.com P. 1/12 Specification of Piezoelectric Ceramic Resonator CSTCR4M00G53-R0 CSTCR4M00G53-B0 Date     Approved by Checked by May 22, 2006   Issued by 1.   Scope は、マイクロコンピュータのクロックにするセラミック (セラロック®)についてします。このにごのにはにへごく ださい。 This product specification is applied to the piezoelectric ceramic resonator used for time base oscillator in a microcomputer. Please contact us when using this product for any other applications than described in the above. 2. び Part Number Murata Part Number テーピング Taping バラ Bulk CSTCR4M00G53-R0 CSTCR4M00G53-B0 Customer's Part Number Customer's Drawing Number 3. び Appearance and Dimensions 3-1 Appearance 3-2 セラロック®の Dimensions of component 3-3 Construction : によってであり、れがありません。 : No illegible marking. No visible dirt. : 1にします。テーピングとバラのは です。 : See Figure 1. Dimensions of taping type and bulk type are the same. : セラミックに、セラミックとを し、キャップでをしております。 : Resonator and capacitor elements are mounted onto ceramic substrate, then metal cap covers over the elements.       Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A www.DataSheet4U.com P. 2/12 4. Electrical Characteristics   4-1 4-2 4-3 4-4 4-5 4-6 4-7 Item   Specification Nominal Oscillating Frequency *1 Initial Tolerance *1 Resonant Impedance (C1,C2) Built-in Load Capacitance (C1,C2) Insulation Resistance Withstanding Voltage Rated Working Voltage (1)   D.C. Voltage (2) A.C. Voltage Frequency Shift by Temperature (-20℃~+80℃のにて) (-20°C to +80°C) Operating Temperature Range Storage Temperature Range エージング *2 Oscillating Frequency Aging *2 4.000MHz ±0.50% ±0.50% max. 60Ω 60Ωmax 15pF±20% () 15pF±20%max. (ref.) 500MΩ (D.C.10V ) 500MΩmin. (Applied D.C.10V) D.C.100V, 5 D.C.100V, 5 seconds max. D.C.6V 15Vp-p. 4-8 4-9 ±0.2% (にし) ±0.2%max. (from initial value) -20℃~+80℃ -20°C to +80°C -55℃~+85℃ -55°C to +85°C ±0.1% (にし) ±0.1%max. (from initial value) *1 セラロック®の1と3をにされた、±0.60%となります。 Terminal (1) and (3) are interchangeable, but if interchange initial tolerance is ±0.60%max. *2 +85±2℃に1000し、1する。 Components shall be left in a chamber of +85±2°C for 1000 hours, then measured after leaving in natural condition for 1 hour.       Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A www.DataSheet4U.com P. 3/12 5. Physical Characteristics Item 5-1 の Specification After Test 1.0m のさからに3させた にがなく、 する。 1 び 4-3 を し ま す。 Components shall be measured after 3 times No visible damage and random dropping on the wooden plate from the the measured values height of 1.0m. shall meet Table 1 and 4-3. 10 ~ 55Hz 、 1.5mm の を 1 び 4-3 を しま X,Y,Zの3に2えたする。 す。 Applying the vibration of amplitude 1.5mm and The measured values vibration frequency 10 to 55Hz in each of 3 shall meet Table 1 and perpendicular directions for 2 hours. 4-3. にすにし、 11 ので5 1 び 4-3 を しま する。 す。 After components soldered on PCB, the load The measured values shall be applied to the PCB as shown in below shall meet Table 1 and figure for 5 times (1 second per 1 time). 4-3. Test Condition Random Drop 5-2 Vibration Resistance 5-3 たわみ Bend Strength PCB Stick 20 10 Load PCB たわみ R10 φ 5 φ 5 Supporter Deflection ± 1センターズレ ±1 Off-Center Part 45 45 み / PCB thickness : 1.6mm / unit : mm       Murata Manufacturing Co.,Ltd. 1 Drawing No. JGC42-4256A www.DataSheet4U.com P. 4/12 5-4 はんだ Resistance to Soldering Heat (1)リフロー プロ ファ イ ル の リフ ロー に 2 した 1 び 4-3 を しま す。 、にりし1する。 (1) Re-flow Components shall be measured after applying The measured values Soldering twice of the re-flow soldering with following shall meet Table 1 and temperature profile and leaving in natural 4-3. condition for 1 hour. Temperature (°C) ピーク Peak (260°C / max.) 230 180 150 Heating (230°C) Gradual Cooling Pre-heating (150-180°C) 30 60 - 120 / sec. sec. min. 40 120 sec. max. sec. min. (2)コテけ +350± 5℃で3.0 ± 0.5て、に 24 にがなく、 にする。し、はんだこては 1 び 4-3 を し ま にしないとする。 す。 (2)Soldering Components shall be measured after soldering No visible damage and with iron at +350±5°C for 3.0±0.5 seconds and leaving in the measured values natural condition for 24 hours. The soldering shall meet Table 1 and iron shall not touch the components while 4-3. soldering. 5-5 はんだ LFはんだ (Sn-3Ag-0.5Cu) の 90% にはん PCTにて+105°C、100%R.H. だがします。 ので、 4のエージングをした、 をロジン メ タ ノ ー ル に 5 した、 +245±5°Cのはんだに3±0.5す。 Solderability LF Solder (Sn-3Ag-0.5Cu) The solder shall coat at After being kept in pressure cooker at +105°C least 90% of the temperature and 100%R.H. for 4 hours, surface of terminal. terminals of components shall be immersed in a soldering bath at temperature of +245±5°C for 3±0.5 seconds after being placed in a rosinmethanol for 5 seconds.       Murata Manufacturing Co.,Ltd. Drawing No. JGC42-4256A www.DataSheet4U.com P. 5/12 6. Environmental Characteristics Item 6-1 Dry Heat (Storage) の Specification After Test +85 ± 2 ℃の に 1000 し、 4-3 び 4-9 を しま にして、1にする。 す。 Components shall be left in a chamber The measur.


CJ2M-CPU31 CSTCR4M00G53-B0 E3T


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)