Document
www.DataSheet4U.com
AR3505 THRU AR3510
Features
· Plastic material used carries Underwriters Laboratory Classification 94V-0 · Low cost construction utilizing void-free molded plastic technique · Low cost · Diffused junctions · Low leakage · High surge capability · High temperature soldering guaranteed : 250¡É for 10 seconds
CURRENT 35.0 Amperes VOLTAGE 50 to 1000 Volts
AR
0.185(4.7) 0.165(4.2)
0.250(6.4) 0.235(6.0)
Mechanical Data
· Case : AR molded plastic · Terminals : Plated terminals, solderable per MIL-STD-750, method 208 · Polarity : Color ring denotes cathode end · Mounting Position : Any · Weight : 0.07 ounce, 1.8 gram
0.225(5.7) 0.215(5.5) 0.410(10.4) 0.380(9.7)
Dimensions in inches and (millimeters)
Maximum Ratings And Electrical Characteristics
(Ratings at 25¡É ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%)
Symbols
Maximum recurrent peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TC=150¡É Peak forward surge current 8.3ms half sine wave superimposed on rated load (JEDEC method) TJ=150¡É Maximum instantaneous forward voltage at 35.0A Maximum DC reverse current at rated DC blocking voltage TC=25¡É TC=100¡É VRRM VRMS VDC I(AV) IFSM VF IR trr CJ R¥è JC TJ TSTG
AR 3505
50 35 50
AR 351
100 70 100
AR 352
200 140 200
AR 354
400 280 400 35.0 500 1.0 5.0 250 3.0 300 1.0 -50 to +175
AR 356
600 420 600
AR 358
800 560 800
AR 3510
1000 700 1000
Units
Volts Volts Volts Amps Amps Volts ¥ìA ¥ìS pF ¡É /W ¡É
Typical reverse recovery time (Note 2) Typical junction capacitance (Note 1) TJ=25¡É Typical thermal resistance (Note 3) Operating and storage temperature range
Notes:
(1) Measured at 1MHz and applied reverse voltage of 4.0V dc. (2) Reverse recovery test conditions:IF=0.5A, IR=1.0A, Irr=0.25A (3) Thermal resistance from junction to case, single side cooled.
www.DataSheet4U.com
RATINGS AND CHARACTERISTIC CURVES AR3505 THRU AR3510
PEAK FORWARD SURGE CURRENT. (A)
AVERAGE FORWARD CURRENT. (A)
35 30 25 20 15 10 5
FIG.1 MAXIMUM FORWARD CURRENT DERATING CURVE
SINGLE PHASE HALF SINE WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD
1000
FIG.2- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT
8.3ms Single Half Wave JEDEC Method
500
100 50 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 1 00
0 125
135 145 155 165 O AMBIENT TEMPERATURE. ( C)
175
FIG.3- TYPICAL FORWARD CHARACTERISTICS 1000
100 INSTANTANEOUS REVERSE CURRENT. ( u A) 60 40 20 10 6 4 2
FIG.4- TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS FORWARD CURRENT. (A)
100
Tj=100 C
O
10
1 0.6 0.4 0.2 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSEVOLTAGE. (%)
Tj=25 OC
1.0
Tj=25 C PULSE WIDTH-300uS 2% DUTY CYCLE
O
0.1 0.6
1.0 1.4 1.8 FORWARD VOLTAGE. (V)
2.2
2.6
FIG.5- TYPICAL JUNCTION CAPACITANCE 1000 JUNCTION CAPACITANCE.(pF)
500
Tj=25 C
O
100 50 1
f=1.0MHz Vsig=50mVp-p
2
5 10 20 50 REVERSE VOLTAGE. (V)
1 00
.