DatasheetsPDF.com

EE-SX461-P11 Dataheets PDF



Part Number EE-SX461-P11
Manufacturers Omron
Logo Omron
Description Photomicrosensor
Datasheet EE-SX461-P11 DatasheetEE-SX461-P11 Datasheet (PDF)

Photomicrosensor (Transmissive) EE-SX461-P11 I Dimensions Note: All units are in millimeters unless otherwise indicated. 171826-3 (Tyco Electronics AMP) I Features • • • • • • Snap-in-mounting model. Mounts to 0.8- to 1.6-mm-thick panels. With a 15-mm-wide slot. Photo IC output signals directly connect with C-MOS and TTL. Connects to Tyco Electronics AMP’s EI-series connectors. RoHS Compliant. I Absolute Maximum Ratings (Ta = 25°C) 2 (Aperture width) Two, R1 (15) Optical axis Item Power supp.

  EE-SX461-P11   EE-SX461-P11



Document
Photomicrosensor (Transmissive) EE-SX461-P11 I Dimensions Note: All units are in millimeters unless otherwise indicated. 171826-3 (Tyco Electronics AMP) I Features • • • • • • Snap-in-mounting model. Mounts to 0.8- to 1.6-mm-thick panels. With a 15-mm-wide slot. Photo IC output signals directly connect with C-MOS and TTL. Connects to Tyco Electronics AMP’s EI-series connectors. RoHS Compliant. I Absolute Maximum Ratings (Ta = 25°C) 2 (Aperture width) Two, R1 (15) Optical axis Item Power supply voltage Output voltage Output current Permissible output dissipation Ambient temperature Operating Storage Symbol VCC VOUT IOUT POUT Topr Tstg Tsol 7V Rated value 28 V 16 mA 250 mW (see note) –20°C to 75°C –40°C to 85°C --- Internal Circuit V O G Soldering temperature Unless otherwise specified, the tolerances are as shown below. Dimensions 3 mm max. 3 < mm ≤ 6 6 < mm ≤ 10 10 < mm ≤ 18 18 < mm ≤ 30 Tolerance Note: Refer to the temperature rating chart if the ambient temperature exceeds 25°C. Terminal No. V O G Name Power supply (Vcc) Output (OUT) Ground (GND) ±0.3 ±0.375 ±0.45 ±0.55 ±0.65 I Ordering Information Description Photomicrosensor (transmissive) Model EE-SX461-P11 Recommended Mating Connectors: Tyco Electronics AMP 171822-3 (crimp connector) 172142-3 (crimp connector) OMRON EE-1005 (with harness) I Electrical and Optical Characteristics (Ta = 25°C, VCC = 5 V±10%) Item Current consumption Low-level output voltage High-level output voltage Response frequency Symbol ICC VOL VOH f 35 mA max. 0.3 V max. (VCC x 0.9) V min. 3 kHz min. Value Condition With and without incident IOUT = 16 mA with incident VOUT = VCC without incident, RL = 47 kΩ VOUT = VCC, RL = 47 kΩ (see note) Note: The value of the response frequency is measured by rotating the disk as shown below. Disk 2.1 mm 0.5 mm 0.5 mm t = 0.2 mm 290 www.DataSheet.in Photomicrosensor (Transmissive) EE-SX461-P11 I Engineering Data Output Allowable Dissipation vs. Ambient Temperature Characteristics Output allowable dissipation Pc (mW) Sensing Position Characteristics (Typical) d1 = 0±1.1 mm VCC = 5 V Ta = 25°C RL = 47 kΩ Output transistor Center of optical axis Ambient temperature Ta (°C) 1,000±20 Distance d (mm) EE-1005 Connector (1) (2) (3) No. 1 2 3 Name Receptacle housing Receptacle contact Lead wire Model 171822-3 170262-1 UL1007 AWG24 Quantity 1 3 3 Maker Tyco Electronics AMP Tyco Electronics AMP --- Wiring Connector circuit no. 1 2 3 Lead wire color Red Orange Yellow Output when connected to EE-SX461-P11 VCC OUT GND I Recommended Mounting Hole Dimensions and Mounting and Dismounting Method Dismounting by Hand Squeeze the mounting tabs as shown in the following illustration and press the mounting tabs upwards. Optical axis EE-SX461-P11 Sensor edge (to post header) Center of sensing slot Sensor edge (2) The Photomicrosensor can be mounted to 0.8- to 1.6-mm-thick panels. Refer to the above mounting hole dimensions and open the mounting holes in the panel to which the Photomicrosensor will be mounted. Insert into the holes the Photomicrosensor’s mounting portions with a force of three to five kilograms but do not press in the Photomicrosensor at one time. The Photomicrosensor can be easily mounted by inserting the mounting portions halfway and then slowly pressing the Photomicrosensor onto the panel. There are two ways to dismount the Photomicrosensor. Refer to the following. Panel (1) (1) Pressed mounting holes are ideal for mounting the Photomicrosensor. When mounting the Photomicrosensor to a panel that has pressed mounting holes for the Photomicrosensor, be sure to mount the Photomicrosensor on the pressing side of the panel, otherwise it may be difficult to mount the Photomicrosensor and an insertion force of five to six kilograms may be required. When mounting the Photomicrosensor to a panel that has mounting holes opened by pressing, make sure that the mounting holes have no burrs, otherwise the lock mechanism of the Photomicrosensor will not work perfectly. After mounting the Photomicrosensor to a panel, be sure to check if the lock mechanism is working perfectly. EE-SX461-P11 Dismounting with Screwdriver Press the mounting hooks of the Photomicrosensor with a flat-blade screwdriver as shown in the following illustration and pull up the Photomicrosensor. EE-SX461-P11 Flat-blade screwdriver (2) (1) Flat-blade screwdriver (1) (2) Light interrupting plate Mounting hook Panel Mounting hook This tapered portion must be on the lower side of the panel, otherwise the Photomicrosensor will not be locked in. Panel Mounting tab Photomicrosensor (Transmissive) EE-SX461-P11 www.DataSheet.in 291 Terms and Conditions of Sale 1. Offer; Acceptance. These terms and conditions (these "Terms") are deemed part of all quotations, acknowledgments, invoices, purchase orders and other documents, whether electronic or in writing, relating to the sale of products or services (collectively, the "Products") by Omron Electronic C.


EE-SX460-P1 EE-SX461-P11 GRM219R60J106K


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)