Document
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Features
* Low power consumption. * High efficiency. * Versatile mounting on p.c. board or panel. * I.C. compatible/low current requirement. * Popular T-13/4 diameter.
Package Dimensions
Part No. LTL2P3TBK5
Lens Water Clear
Source Color InGaN Blue
Notes: 1. All dimensions are in millimeters (inches). www.DataSheet4U.com 2. Tolerance is ±0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice.
Part No. : LTL2P3TBK5 BNS-OD-C131/A4
Page :
1
of
10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Absolute Maximum Ratings at TA=25℃
Parameter Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6mm(.063") From Body] Maximum Rating 120 100 30 5 -25°C to + 80°C -30°C to + 100°C 260°C for 5 Seconds Unit mW mA mA V
www.DataSheet4U.com
Part No. : LTL2P3TBK5 BNS-OD-C131/A4
Page :
2
of
10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Electrical / Optical Characteristics at TA=25℃
Parameter Luminous Intensity Viewing Angle Peak Emission Wavelength Dominant Wavelength Spectral Line Half-Width Forward Voltage Reverse Current Symbol IV 2θ1/2 λP λd ∆λ VF IR Min. 880 Typ. 2500 15 Max. Unit mcd deg nm nm nm 3.8 100 V µA IF = 20mA VR = 5V Test Condition IF = 20mA Note 1,5 Note 2 (Fig.6) Measurement @Peak (Fig.1) Note 3
468 470 25 3.5
NOTE: 1. Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. θ1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 3. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 4. Iv classification code is marked on each packing bag. 5. The Iv guarantee should be added ±15% tolerance. 6. Precautions in handling: • When soldering, leave 2mm of minimum clearance from the resin to the soldering point. • Dipping the resin to solder must be avoided. • Correcting the soldered position after soldering must be avoided. • In soldering, do not apply any stress to the lead frame particularly when heated. • When forming a lead, make sure not to apply any stress inside the resin. • Lead forming must be done before soldering. www.DataSheet4U.com • It is necessary to cut the lead frame at normal temperature. 7. Caution in ESD: Static Electricity and surge damages the LED. It is recommend to use a wrist band or anti-electrostatic glove when handling the LED. All devices, equipment and machinery must be properly grounded. Part No. : LTL2P3TBK5 BNS-OD-C131/A4 Page : 3 of 10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Typical Electrical / Optical Characteristics Curves
(25℃ Ambient Temperature Unless Otherwise Noted)
www.DataSheet4U.com
Part No. : LTL2P3TBK5 BNS-OD-C131/A4
Page :
4
of
10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Packing Spec
500 or 250 pcs per packing bag
10 packing bags per inner carton total 5000 pcs per inner carton
8 Inner cartons per outer carton total 40000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing
www.DataSheet4U.com
Part No. : LTL2P3TBK5 BNS-OD-C131/A4
Page :
5
of
10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
Bin Code List For Reference
Luminous Intensity Bin Code P Q R S T U Min. 880 1150 1500 1900 2500 3200 Unit : mcd @20mA Max. 1150 1500 1900 2500 3200 4200
Note: Tolerance of each bin limit is ±15% Dominant Wavelength Bin Code B08 B09 Min. 465.0 470.0 Unit : nm @20mA Max. 470.0 475.0
Note: Tolerance of each bin limit is ±1nm
www.DataSheet4U.com
Part No. : LTL2P3TBK5 BNS-OD-C131/A4
Page :
6
of
10
LITE-ON TECHNOLOGY CORPORATION
Property of Lite-On Only
CAUTIONS
1. Application
The LEDs described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).Consult Liteon’s Sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices).
2. Storage
The storage ambient for the LEDs should not exceed 30°C temperature or 70% relative humidity. It is recommended that LEDs out of their original packaging are used within three months. For extended storage out of their original packaging, it is recommended that the LEDs be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient.
3. Cleaning
Use alcohol-based cleaning solvents such as isopro.