Inverter Module. LXMG1643-12-62 Datasheet

LXMG1643-12-62 Module. Datasheet pdf. Equivalent

Part LXMG1643-12-62
Description CCFL Programmable Inverter Module
Feature PanelMatch™ TM ® LXMG1643-12-62 12V Quad 6W CCFL Programmable Inverter Module P RODUCTION D ATA S.
Manufacture Microsemi Corporation
Total Page 6 Pages
Datasheet
Download LXMG1643-12-62 Datasheet



LXMG1643-12-62
PanelMatch™
LXMG1643-12-62
TM ® 12V Quad 6W CCFL Programmable Inverter Module
PRODUCTION DATA SHEET
DESCRIPTION
The LXMG1643-12-62 is a Quad 6W The resultant “burst drive” that
Output Direct Drive™ CCFL (Cold energizes the lamp was designed
wwwC.DatahtaoSdheeet4UF.nleutorescent Lamp) Inverter specifically to ensure that no premature
Module specifically designed for driving lamp degradation occurs, while allowing
LCD backlight lamps. It is ideal for significant power savings at lower dim
driving typical 12.1” to 18.1” TFT panels. levels.
LXMG1643 modules provide the The modules convert DC voltage from
designer with a vastly superior display the system battery or AC adapter directly
brightness range then typical with analog to high frequency, high-voltage waves
(amplitude control) dimming.
required to ignite and operate CCFL
The inverter includes a dimming input lamps.
that permits brightness control from either The LXMG1643-12-62 inverter is
a DC voltage source or a PWM signal or intended for panel assemblies with
external Potentiometer. The maximum individual lamp connections, or where
output current is externally programmable lamps are spaced apart from each other.
over a range of 5 to 8mA in 1mA steps to The LXMG1643-12-61 inverter should be
allow the inverter to properly match to a used for panel applications where lamp
wide array of LCD panel lamp current pairs are in close proximity and share a
specifications.
common return (low side) wire.
RangeMAX™ Digital Dimming Other benefits of this new topology
Technique provides flicker-free brightness are stable fixed-frequency operation,
control in any wide range (typically 50:1+) secondary-side strike-voltage regulation
dimming application.
and both open/shorted lamp protection
with fault timeout.
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
Protected By U.S. Patents: 5,923,129; 5,930,121; 6,198,234; Patents Pending
PRODUCT HIGHLIGHT
KEY FEATURES
ƒ Externally Programmable
Maximum Output Current
ƒ Easy to Use Brightness
Control
ƒ RangeMAX™ Wide Range
Dimming
ƒ Output Short-Circuit Protection
and Automatic Strike-Voltage
Regulation and Timeout
ƒ Fixed Frequency Operation
ƒ Rated From -20 to 70°C
ƒ UL 60950 E175910
ƒ RoHS Compliant
APPLICATIONS
ƒ High Brightness Displays
ƒ Desktop Displays
ƒ Industrial Display Controls
BENEFITS
ƒ Smooth, Flicker Free 2%-
100% Full-Range Brightness
Control
ƒ Programmable Output
Current Allows Inverter to
Mate With a Wide Variety of
LCD Panel Specifications
ƒ
Universal Dimming Input PWM, VDC, or Potentiometer
HI HI
DC Voltage
Source
Potentiometer
PWM
Signal
Microsemi
Selectable Maximum Output Current 5mA to 8mARMS
HI
HI
PART NUMBER
LXMG1643-12-62
PACKAGE ORDER INFO
OUTPUT CONNECTORS
Four JST SM02B-BHSS-1-TB(LF)(SN) or Yeon Ho 35001WR-02A00
INVERTER MATES DIRECTLY
TO PANEL CONNECTORS
JST BHSR-02VS-1
Copyright © 2005
Rev. 1.1, 2006-11-16
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1



LXMG1643-12-62
PanelMatch™
LXMG1643-12-62
TM ® 12V Quad 6W CCFL Programmable Inverter Module
PRODUCTION DATA SHEET
ABSOLUTE MAXIMUM RATINGS (NOTE 1)
Input Signal Voltage (VIN1).....................................................................................................................................-0.3V to 15V
Input Power ....................................................................................................................................................................... 30W
Output Voltage, no load ............................................................................................................ Internally Limited to 2000VRMS
Output Current (each output) ......................................................................................................9.5mARMS (Internally Limited)
Output Power (each output) ............................................................................................................................................. 6.0W
Input Signal Voltage ( SLEEP Input) ...................................................................................................................... -0.3V to VIN1
Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V
Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C
Storage Temperature Range...............................................................................................................................-40°C to 85°C
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
terminal.
RECOMMENDED OPERATING CONDITIONS (R.C.)
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Parameter
Symbol
Recommended Operating Conditions
Min R.C. Max
Input Supply Voltage Range (Fully Regulated
Lamp Current)
VIN1
10.8
12
13.2
Input Supply Voltage Range (Functional)
10.2 12 13.8
Output Power (each output)
PO 5.0 6.0*
Linear BRITE Control Input Voltage Range
VBRT_ADJ
0.5
2.0
Lamp Operating Voltage
VLAMP
530
625
730
Lamp Current (Full Brightness)
IOLAMP
5
8
Operating Ambient Temperature Range
TA -20
70
*Total output power must not exceed 6W. Higher voltage lamps may require maximum output current to be set lower than 8mARMS
Units
V
W
V
VRMS
mARMS
°C
ELECTRICAL CHARACTERISTICS
The following specifications apply over the recommended operating condition and ambient temperature of 25°C except where otherwise
noted.
Parameter
Symbol
Test Conditions
` OUTPUT PIN CHARACTERISTICS
Full Bright Lamp Current (each output)
Full Bright Lamp Current (each output)
Full Bright Lamp Current (each output)
Full Bright Lamp Current (each output)
Output Current Lamp to Lamp
Deviation
Min. Average Lamp Current
(each output)
Lamp Start Voltage
Operating Frequency
Burst Frequency
IL(MAX)
IL(MAX)
IL(MAX)
IL(MAX)
ILL%DEV
IL(MIN)
VLS
fO
fBURST
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Ground, ISET2 = Ground
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Ground, ISET2 = Open
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Open, ISET2 = Ground
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Open, ISET2 = Open
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Open, ISET2 = Open
VBRT_ADJ 0.5VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = ISET2 = Ground
-20°C < TA < 70°C, VIN1 > 10.8VDC
VBRT_ADJ = 2.5VDC, SLEEP > 2.0V, VIN1 = 12V
Output Burst Frequency
LXMG1643-12-62 Units
Min Typ Max
4.0 5
5.0 6
6.0 7
7.0 8
3
1500
69
269
.30
1650
72
281
5.5 mARMS
6.6 mARMS
7.7 mARMS
8.8 mARMS
10 %
mARMS
VRMS
75 kHz
293 Hz
Copyright © 2005
Rev. 1.1, 2006-11-16
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)