Document
26cm COLOUR TFT-LCD MODULE (10.4 TYPE) LIQUID CRYSTAL DISPLAY DIVISION PRODUCT INFORMATION
LTM10C273 (a-Si TFT)
FEATURES
(1) (2) (3) (4) 10.4” SVGA color display with High Luminance Built in Long Life Lamps(30,000 h) Replaceable structure of lamp units Full mechanical compatible with LTM10C209H, LTM10C209A (10.4” VGA)
TENTATIVE
MECHANICAL SPECIFICATIONS
Item Dimensional Outline (typ.) Number of Pixels Active Area Pixel Pitch Weight (approximately) Backlight Specifications 265.0(W) x 188.8(H) x 12max(D) mm 800(W) x 600(H) pixels 211.2(W) x 158.4(H) mm 0.264(W) x 0.264(H) 580g Twin CCFLs, Sidelight type
ABSOLUTE MAXIMUM RATINGS
Item (VDD) (VFL) FL Driving Frequency (fFL) Input Signal Voltage (VIN) Operating Temperature Storage Temperature Storage Humidity (Max. wet bulb temperature = 39°C) Supply Voltage Min. -0.3 0 0 -0.3 0 -20 10 Max. 7.0 2.0 100 VDD+0.3 50 60 90 Unit V kV(rms) kHz V °C °C %(RH)
ELECTRICAL SPECIFICATION (Ta=25°C)
Item Supply Voltage FL Start Voltage High Level Input Voltage (VIH) Low Level Input Voltage (VIL) *1 Current Consumption (IDD) *2 (IFL) *1 *2 Power Consumption
*1 : 8 color bars pattern *2 : Except the efficiency of FL inverter
(VDD) (VFL)
Min. 4.75 500 1500 3.5 0 --3.0 ---
Typ. 5.0 550 ------200 6.0 7.6
Max. 5.25 600 1800 VDD 1.5 320 7.0 ---
Unit V V(rms) V(rms) V mA mA(rms) W
Remarks
Ta=0°C
IFL =6.0mArms
OPTICAL SPECIFICATION (Ta=25°C)
Item Contrast Ratio (CR) Response Time Luminance (L) Min. 100 ----190 Typ. 250 ----250 Max. --50 50 --Unit --ms ms cd/m2 Remarks
(tON) (tOFF)
IFL=6.0mArms
*The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by Toshiba or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Toshiba or others. *The information contained herein may be changed without prior notice. It is therefore advisable to contact Toshiba before proceeding with the design of equipment incorporating this product.
(1/9)
www.DataSheet4U.net
2000-06-06 (Ver.4.0)
265.0
4- f 3.2
3.0
3.5
8.0
7.0
3.5
DIMENSIONAL OUTLINE
9 3 211.2 (Active Area) 215.2 (Viewing Area) 127.0 _ 0.4 130 + 188.6 9 3 3 3.5
(2.7)
8.0
7.0
27.5 10.8
161.1 163.4 (Bezel Openning) _ 0.4 130.0 + 65.0 (Active/Viewing Area Center) 3.5
158.4 (Active Area) 162.4 (Viewing area)
3.5
TENTATIVE
(2/9)
2.5 4.5 12.0max 252.0 (253.0) _ 0.4 259 + (262.0)
3.0
3.5 19.9 216.2 (Bezel Openning) 128.0(Active/Viewing Area Center)
Unit : mm
Standard tolerance : ±0.5
2000-06-06 (Ver.4.0)
LTM10C273
3.0 80 •}10
Low Voltage No.3
4.0
4.0 3.0
4.0
4.0
‚b ‚m ‚R
4.0
10.0 3.0
;
DIMENSIONAL OUTLINE
High Voltage No.1
38.0
4mm MAX height components are placed
20.0
No.31
15.0
CN1 No.1
No.2
2.5
4.0
4.0
3.0 3.0 4.0
4.0
High Voltage No.1
TENTATIVE
7.0 •}0.5
(3/9)
Bezel Surface PCB I/F Connector User side Connector
4.0-ƒÓ4 80 •}10
(frame)
Low Voltage No.3
‚b ‚m ‚Q
3.0
4.0
Unit : mm
Standard tolerance : ±0.5
2000-06-06 (Ver.4.0)
Sectional figure of I/F connector
LTM10C273
LTM10C273 BLOCK DIAGRAM
CN2 Backlight CN1 Connector X-driver IC Panel Controller DC/DC Converter
Liquid Crystal Panel Y-driver IC 800 x 600 pixels
VBB
Gray scale Manipulation Voltage Generation Circuit
VGG
Backlight
CN3
(4/9)
2000-06-06 (Ver.4.0)
(1) Vertical Timing
t 1 t 2
TIMING CHART
NCLK
t 3 t 3
ENAB
X,1 X,2 X,3 X,4 X,598 X,599 X,600 X,Y
R5-R0 G5-G0 B5-B0
(2) Horizontal Timing
t 3 t 4 t c
(5/9)
797,Y 1,Y 2,Y 3,Y 4,Y 5,Y 6,Y 7,Y X,Y 798,Y
NCLK
799,Y
ENAB R5-R0 G5-G0 B5-B0
800,Y
t6
t5 t7 a VIH (MIN):3.5(V) VIL (MAX):1.5(V) t8 t9 VALID DATA Input Signal Center Level:0.5VDD VIH (MIN):3.5(V) VIL (MAX):1.5(V) b
NCLK
NCLK
0.5VDD + 10% Duty(a,b):50 _
2000-06-06 (Ver.4.0)
ENAB R5-R0 G5-G0 B5-B0
LTM10C273
LTM10C273 TIMING SPECIFICATION 1) 2) 3) 4) 5)
Item Frame Period Vertical Display Term One Line Scanning Time Horizontal Display Term Clock Period Clock “L” Time Clock “H” Time Set Up Time Hold Time Symbol t1 t2 t3 t4 tc t6 t7 t8 t9 Min. 604 x t3 600 x t3 844 x tc 26.4 800 x tc 25.0 9.0 9.0 4.0 5.0 Typ. 625 x t3 17.78 600 x t3 1024 x tc 28.44 800 x tc 27.78 --------Max. 628 x t3 17.86 600 x t3 1056 x tc --800 x tc ----------Unit --ms ----µs --ns ns ns ns ns Remarks
t2=N x t3
Note 1)
When ENAB is fixed to “H” level or “L” level after NCLK input, the panel is displayed as black. However, it may be occurred a flicker on the display.
Note 2) Note 3) Note 4)
When NCLK is fixed to “H” level or “L” level, the panel becomes white stage after several seconds. Do not change t1 and t3 values in the operation. When t1 or t3 is changed, the panel is displayed as black. Please adjust LCD operating signal timing and FL driving frequency, to optimize the display quality. There is a possibility that flicker is observed by the interference of LCD operating signal timing and FL driving condition (especially driving frequency).
Not.