Document
Conductive polymer chip tantalum capacitors (Bottom surface electrode type : Large capacitance)
TCTO Series AL Case
Features (AL) 1) Conductive polymer used for the cathode material. 2) Ultra low ESR 3) Small package, but big capacitance 4) Screening by thermal shock Dimensions (Unit : mm)
Anode mark
(Unit : mm)
H W1
Dimensions L W1 W2
W2
AL case 3.2 + − 0.2 1.6 + − 0.2 1.2 + − 0.2 1.1 + − 0.1 0.8 + − 0.2
L
H S
S
S
Part No. Explanation
T C T O
1
A L
2
0
3
J
4
7
4
www.DataSheet.co.kr
6
M
5
8 R
6
1 Series name
TCTO
4 Nominal capacitance Nominal capacitance in pF in 3 digits: 2 significant figures followed by the figure representing the number of 0's. 5 Capacitance tolerance
2 Case style
AL
3 Rated voltage
Rated voltage (V) CODE 2.5 4 6.3 10 0E 0G 0J 1A
M: + − 20%
6 Taping
8 : Tape width R : Positive electrode on the side opposite to sprocket hole
This specification has possibility of charge, due to underdevelopment product. Please ask for latest specification to our sales.
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved. ○
1/5
2012.03 - Rev.E
Datasheet pdf - http://www.DataSheet4U.net/
TCTO Series AL Case
Rated table
ESR : mΩ
Data Sheet
(μF) 22 (226) 33 (336) 47 (476) 68 (686) 100 (107) 150 (157) 220 (227)
Under development
Rated voltage (V.DC) 2.5 4 6.3 10 200 200 200 ∗ 200 ∗70/200
200 200 ∗ 200 200
Marking
The indications listed below should be given on the surface of a capacitor. (1) Polarity : The polarity should be shown by bar. (on the anode side) (2) Rated DC voltage : Due to the small size of AL case, a voltage code is used as shown below. (3) Visual typical example (1) voltage code (2) capacitance code Voltage Code e g j A Rated DC Voltage (V) 2.5 4 6.3 10 Capacitance Code j n s w a e Nominal Capacitance (μF) 22 33 47 68 100 150
[AL case]
note 1)
j s − − (1) (2)
www.DataSheet.co.kr
js
manufacture code note 2) voltage code and capacitance code are variable with parts number
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved. ○
2/5
2012.03 - Rev.E
Datasheet pdf - http://www.DataSheet4U.net/
TCTO Series AL Case
Characteristics
Item Operating Temperature
Maximum operating temperature with no voltage derating
Data Sheet
Performance −55°C to +105°C +85°C 2.5 4 6.3 10 2 3.2 5 3.2 5 8
Test conditions (based on JIS C 5101−1 and JIS C 5101−3) Voltage reduction when temperature exceeds +85°C
Rated voltage (VDC) Category voltage (VDC) Surge voltage (VDC) DC Leakage current
at 85°C at 105°C at 85°C As per 4.9 JIS C 5101-1 As per 4.5.1 JIS C 5101-3 Voltage : Rated voltage for 5min As per 4.7 JIS C 5101-1 As per 4.5.2 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC : DC Equivalent series circuit Measuring circuit As per 4.8 JIS C 5101-1 As per 4.5.3 JIS C 5101-3 Measuring frequency : 120±12Hz Measuring voltage : 0.5Vrms +1.5 to 2V.DC : DC Equivalent series circuit Measuring circuit As per 4.10 JIS C 5101-1 As per 4.5.4 JIS C 5101-3 Measuring frequency : 100±10kHz Measuring voltage : 0.5Vrms or less : DC Equivalent series circuit Measuring circuit As per 4.14 JIS C 5101-1 As per 4.6 JIS C 5101-3 Dip in the solder bath Solder temp : 240±5°C Duration : 10±0.5s Repetition :1 After the specimens, leave it at room temperature for over 24h and then measure the sample. As per 4.16 JIS C 5101-1 As per 4.10 JIS C 5101-3 Repetition : 5 cycles (1 cycle : steps 1 to 4) without discontinuation.
www.DataSheet.co.kr
8 13
Shall be satisfied the voltage on " Standard list "
Capacitance tolerance
Shall be satisfied allowance range. ±20%
Tangent of loss angle (Df, tan δ)
Shall be satisfied the voltage on " Standard list "
ESR
Shall be satisfied the voltage on " Standard list "
Resistance to Soldering heat
Appearance L.C. ΔC / C Df (tan δ)
There should be no significant abnormality. The indications should be clear. Less than 300% of initial limit Within ±20% of initial value Less than 300% of initial limit
Temperature cycle
Appearance L.C. ΔC / C Df (tan δ)
There should be no significant abnormality. The indications should be clear. Less than 1000% of initial limit Within ±20% of initial value Less than 300% of initial limit
Temp. 1 2 3 4 −55±3°C Room temp. 105±2°C Room temp.
Time 30±3min. 3min. or less 30±3min. 3min. or less
Moisture resistance
Appearance L.C. ΔC / C Df (tan δ)
There should be no significant abnormality. The indications should be clear. Less than 300% of initial limit Within +30/−20% of initial value Less than 300% of initial limit
As per 4.22 JIS C 5101-1 As per 4.12 JIS C 5101-3 After leaving the sample under such atmospheric condition that the temperature and humidity are 40±2°C and 90 to 95% RH, respectiveiy, for 500±12h leave it at room temperature for 24h and then measure the sample.
www.rohm.com
c 2012 ROHM Co., Ltd. All rights reserved. ○
3/5
2012.03 - Rev.E
Datasheet pdf - http://www.DataSheet4U.net/
TCTO Series AL Case
Item
Temperature Stability Temp.
Data Sheet
Performance Test .