Document
Preliminary‡
152-Ball NAND Flash and Mobile LPDRAM PoP (TI OMAP) MCP Features
NAND Flash and Mobile LPDRAM
152-Ball Package-on-Package (PoP) Combination Memory (TI OMAP™) MT29C Family
Current production part numbers: See Table 1 on page 3
Features
Figure 1:
PoP Block Diagram
• Micron® NAND Flash and Mobile LPDRAM components • RoHS-compliant, “green” package • Separate NAND Flash and Mobile LPDRAM interfaces • Space-saving package-on-package combination • Low-voltage operation (1.70–1.95V) • Industrial temperature range: –40°C to +85°C
NAND Flash Power
NAND Flash Device
NAND Flash Interface
NAND Flash-Specific Features
• Organization – Page size x8: 2112 bytes (2048 + 64 bytes) x16: 1056 words (1024 + 32 words) – Block size: 64 pages (128K + 4K bytes)
LP-DRAM Power
www.DataSheet.net/
LP-DRAM Device
LP-DRAM Interface
Mobile LPDRAM-Specific Features
• • • • • • • • No external voltage reference required No minimum clock rate requirement 1.8V LVCMOS-compatible inputs Programmable burst lengths Partial-array self refresh (PASR) Deep power-down (DPD) mode Selectable output drive strength STATUS REGISTER READ (SRR) supported1
Options
• LP-DRAM 166 MHz CL32 133 MHz CL3
Marking
-6 -75
Notes: 1. Contact factory for remapped SRR output. 2. CL = CAS (READ) latency.
PDF: 09005aef8326e5ac / Source: 09005aef8326e59a 152ball_ nand_lpdram_j4xx_omap.fm - Rev. E 4/09 EN
1
Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2008 Micron Technology, Inc. All rights reserved.
‡Products and specifications discussed herein are for evaluation and reference purposes only and are subject to change by Micron without notice. Products are only warranted by Micron to meet Micron’s production data sheet specifications.
Datasheet pdf - http://www.DataSheet4U.co.kr/
Preliminary
152-Ball NAND Flash and Mobile LPDRAM PoP (TI OMAP) MCP Part Numbering Information – 152-Ball PoP
Part Numbering Information – 152-Ball PoP
Micron NAND Flash and LPDRAM devices are available in different configurations and densities. Figure 2: 152-Ball Part Number Chart
MT 29C 1G 24M Micron Technology Product Family
29C = NAND + LPDRAM MCP
A
C
J
A
CG
–x
IT
ES Production Status
Blank = Production ES = Engineering sample MS = Mechanical sample
NAND Density
1G = 1Gb 2G = 2Gb 4G = 4Gb
Operating Temperature Range
IT = Industrial (–40° to +85°C)
LPDRAM Self Refresh Current
Blank = Standard
LPDRAM Density
12M = 512Mb 24M = 1024Mb 48M = 2048Mb
LPDRAM Access Time
–6 166 MHz CL3 –75 133 MHz CL3
Operating Voltage Range
A = 1.8V (1.70–1.95V)
Package Codes
CA = 152-ball PoP VFBGA (14 x 14 x 0.9mm) CG = 152-ball PoP VFBGA (14 x 14 x 1.0mm)
www.DataSheet.net/
NAND Flash Configuration
Width Density Generation
JQ = 152-ball PoP TFBGA (14 x 14 x 1.1mm)
C D J K N P U V
x8 x16 x8 x16 x8 x16 x8 x16
1Gb 1Gb 2Gb 2Gb 4Gb 4Gb 1Gb 1Gb
First First Second Second First First Second Second
Chip Count LPDRAM Configuration
Type Width Density Generation CE#, CS# Chip Count
A B C D
1, 1 1, 1 1, 2 1, 2
1 NAND, 1 DRAM 2 NAND, 1 DRAM 1 NAND, 2 DRAM 2 NAND, 2 DRAM
J L N R
DDR DDR DDR DDR
x16 x32 x16 x32
1Gb 1Gb 512Mb 512Mb
First First Second Second
Note:
Not all possible combinations are available. Contact factory for availability.
PDF: 09005aef8326e5ac / Source: 09005aef8326e59a 152ball_ nand_lpdram_j4xx_omap.fm - Rev. E 4/09 EN
2
Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2008 Micron Technology, Inc. All rights reserved.
Datasheet pdf - http://www.DataSheet4U.co.kr/
Preliminary
152-Ball NAND Flash and Mobile LPDRAM PoP (TI OMAP) MCP Device Marking
Table 1: Production Part Numbers
NAND Product MT46H32M32LFJG-6 IT MT46H32M32LFJG-6 IT MT46H32M32LFJG-6 IT MT46H32M32LFJG-6 IT MT46H16M32LFCM-6 IT MT46H16M32LFCM-6 IT MT46H32M32LFJG-6 IT MT46H32M32LFJG-6 IT MT46H16M32LFCM-6 IT MT46H16M32LFCM-6 IT MT46H16M32LFCM-6 IT MT46H16M32LFCM-6 IT LPDDR Product MT29F4G16ABCWC-ET MT29F4G16ABCWC-ET MT29F4G16ABCWC-ET MT29F4G16ABCWC-ET MT29F1G16ABBHC-ET MT29F1G16ABBHC-ET MT29F2G16ABDHC-ET MT29F2G16ABDHC-ET MT29F1G08ABCHC-ET MT29F1G08ABCHC-ET MT29F1G16ABCHC-ET MT29F1G16ABCHC-ET Physical Part Marking JW399 JW400 JW297 JW296 JW226 JW227 JW188 JW189 JW385 JW384 JW375 JW374
Part Number MT29C4G48MAPLCCA-6 IT MT29C4G48MAPLCCA-75 IT MT29C4G48MAPLCJQ-6 IT MT29C4G48MAPLCJQ-75 IT MT29C1G12MADRACG-6 IT MT29C1G12MADRACG-75 IT MT29C2G24MAKLACG-6 IT MT29C2G24MAKLACG-75 IT MT29C1G12MAURACA-6 IT MT29C1G12MAURACA-75 IT MT29C1G12MAVRACA-6 IT MT29C1G12MAVRACA-75 IT
Device Marking
Due to the size of the package, the Micron-standard part number is not printed on the top of the device. Instead, an abbreviated device mark consisting of a 5-digit alphanumeric code is used. The abbreviated device marks are cross-referenced to the Micron part numbers at the FBGA Part Marking Decoder site: www.micron.com/decoder. To view the location of the abbreviated mark on the device, refer to customer se.