DatasheetsPDF.com

F971A106MAA Dataheets PDF



Part Number F971A106MAA
Manufacturers Nichicon
Logo Nichicon
Description SOLID TANTALUM ELECTROLYTIC CAPACITORS
Datasheet F971A106MAA DatasheetF971A106MAA Datasheet (PDF)

SOLID TANTALUM ELECTROLYTIC CAPACITORS F97 Resin-molded Chip, High Reliability (High temperature / moisture resistance) Series Specifications Item Category Temperature Range Capacitance Tolerance Performance Characteristics --55 to +125˚C (Rated temperature : +85˚C) ± 20%, ± 10% (at 120Hz) Refer to next page Refer to next page Compliant to the RoHS directive (2002/95/EC). Compliant to AEC-Q200. Dissipation Factor ESR (100kHz) Leakage Current∗ • After 1 minute' s application of rated volt.

  F971A106MAA   F971A106MAA



Document
SOLID TANTALUM ELECTROLYTIC CAPACITORS F97 Resin-molded Chip, High Reliability (High temperature / moisture resistance) Series Specifications Item Category Temperature Range Capacitance Tolerance Performance Characteristics --55 to +125˚C (Rated temperature : +85˚C) ± 20%, ± 10% (at 120Hz) Refer to next page Refer to next page Compliant to the RoHS directive (2002/95/EC). Compliant to AEC-Q200. Dissipation Factor ESR (100kHz) Leakage Current∗ • After 1 minute' s application of rated voltage,leakage current at 20˚C is not more than 0.01CV or 0.5µA, whichever is greater. • After 1 minute' s application of rated voltage,leakage current at 85˚C is not more than 0.1CV or 5µA,whichever is greater. • After 1 minute' s application of derated voltage,leakage current at 125˚C is not more than 0.125CV or 6.3µA,whichever is greater. +15% Max. (at +125˚C) +10% Max. (at +85˚C) --10% Max. (at --55˚C) At 85˚C, 85% R.H.,For 1000 hours (No voltage applied) Capacitance Change • • • • • • Within ±10% of the initial value Dissipation Factor • • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • 125% or less than the initial specified value After 500 hour' s application of rated voltage in series with a 33Ω resistor at 60˚C, 90 to 95% R.H.,capacitors meet the characteristics requirements table below. Capacitance Change • • • • • • Within ±10% of the initial value Dissipation Factor • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • 125% or less than the initial specified value At --55˚C / +125˚C,For 30 minutes each,1000 cycles Capacitance Change • • • • • • Within ± 5% of the initial value Dissipation Factor • • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • • Initial specified value or less 10 seconds reflow at 260˚C, 5 seconds immersion at 260˚C. Capacitance Change • • • • • • Within ± 5% of the initial value Dissipation Factor • • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • • Initial specified value or less After immersing capacitors completely into a solder pot at 245˚C for 2 to 3 seconds,more than 3/4 of their electrode area shall remain covered with new solder. After application of surge in series with a 33Ω resistor at the rate of 30 seconds ON, 30 seconds OFF,for 1000 successive test cycles at 85˚C,capacitors shall meet the characteristic requirements table below. Capacitance Change • • • • • • Within ± 5% of the initial value Dissipation Factor • • • • • • • • • • • Initial specified value or less Leakage Current • • • • • • • • • • • • • Initial specified value or less After 2000 hours' application of rated voltage in series with a 3Ω resistor at 85˚C,or derated voltage in series with a 3Ω resistor at 125˚C,capacitors shall meet the characteristic requirements table below. Capacitance Change • • • • • • Within ±10% of the initial value Dissipation Factor • • • • • • • • • • • Initial .


F971A685MBA F971A106MAA F971A106MBA


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)