Regulators. ADP5024 Datasheet

ADP5024 Regulators. Datasheet pdf. Equivalent

Part ADP5024
Description Regulators
Feature Data Sheet FEATURES Main input voltage range: 2.3 V to 5.5 V Two 1200 mA buck regulators and one 300.
Manufacture Analog Devices
Datasheet
Download ADP5024 Datasheet




ADP5024
Data Sheet
FEATURES
Main input voltage range: 2.3 V to 5.5 V
Two 1200 mA buck regulators and one 300 mA LDO
24-lead, 4 mm × 4 mm LFCSP package
Regulator accuracy: ±3%
Factory programmable or external adjustable VOUTx
3 MHz buck operation with forced PWM and automatic
PWM/PSM modes
BUCK1/BUCK2: output voltage range from 0.8 V to 3.8 V
LDO: output voltage range from 0.8 V to 5.2 V
LDO: input supply voltage from 1.7 V to 5.5 V
LDO: high PSRR and low output noise
APPLICATIONS
Power for processors, ASICS, FPGAs, and RF chipsets
Portable instrumentation and medical devices
Space constrained devices
Dual 3 MHz, 1200 mA Buck
Regulators with One 300 mA LDO
ADP5024
GENERAL DESCRIPTION
The ADP5024 combines two high performance buck regula-
tors and one low dropout (LDO) regulator in a small, 24-lead,
4 mm × 4 mm LFCSP to meet demanding performance and
board space requirements.
The high switching frequency of the buck regulators enables tiny
multilayer external components and minimizes the board space.
When the MODE pin is set high, the buck regulators operate in
forced PWM mode. When the MODE pin is set low, the buck
regulators operate in PWM mode when the load current is above
a predefined threshold. When the load current falls below a pre-
defined threshold, the regulator operates in power save mode
(PSM), improving the light load efficiency.
The two bucks operate out of phase to reduce the input capacitor
requirement. The low quiescent current, low dropout voltage, and
wide input voltage range of the LDO extends the battery life of
portable devices. The ADP5024 LDO maintains power supply
rejection greater than 60 dB for frequencies as high as 10 kHz
while operating with a low headroom voltage.
Regulators in the ADP5024 are activated though dedicated
enable pins. The default output voltages can be either externally
http://www.DataSheet4U.net/ set in the adjustable version or factory programmable to a wide
range of preset values in the fixed voltage version.
2.3V TO
5.5V
1.7V TO
5.5V
CAVIN
0.1µF
C1
4.7µF
ON
OFF
C2
4.7µF
ON
OFF
C3
1µF
TYPICAL APPLICATION CIRCUIT
AVIN
VIN1
EN1
VIN2
EN2
HOUSEKEEPING
BUCK1
EN1 MODE
MODE
BUCK2
EN2
VOUT1
SW1
FB1
PGND1
MODE
VOUT2
SW2
FB2
PGND2
L1 1µH
R1
R2
VOUT1 AT
1200mA
C5
10µF
PWM
PSM/PWM
L2 1µH
R3
R4
VOUT2 AT
1200mA
C6
10µF
EN3
VIN3
EN3 LDO
(ANALOG)
ADP5024
AGND
VOUT3
FB3
R5
R6
VOUT3 AT
300mA
C7
1µF
Figure 1.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2011-2012 Analog Devices, Inc. All rights reserved.
datasheet pdf - http://www.DataSheet4U.net/



ADP5024
ADP5024
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications....................................................................................... 1
General Description ......................................................................... 1
Typical Application Circuit ............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
General Specifications ................................................................. 3
BUCK1 and BUCK2 Specifications ........................................... 4
LDO Specifications ...................................................................... 5
Input and Output Capacitor, Recommended Specifications.. 6
Absolute Maximum Ratings............................................................ 7
Thermal Resistance ...................................................................... 7
ESD Caution.................................................................................. 7
Pin Configuration and Function Descriptions............................. 8
Typical Performance Characteristics ............................................. 9
REVISION HISTORY
1/1—Rev. 0 to Rev. A
Changes to Features Section and Figure 1..................................... 1
Changes to Table 2............................................................................ 4
Changes to Table 3............................................................................ 5
Changes to Table 4............................................................................ 6
Changes to Table 7............................................................................ 8
Changes to Figure 34...................................................................... 14
Changes to LDO Section and Figure 48 ...................................... 20
Changes to Table 9 and Figure 50................................................. 22
Changes to Buck Regulator Power Dissipation Section ............ 24
Changes to Figure 52 and Figure 53............................................. 27
Changes to Ordering Guide .......................................................... 28
8/11—Revision 0: Initial Version
Data Sheet
Theory of Operation ...................................................................... 16
Power Management Unit........................................................... 17
BUCK1 and BUCK2 .................................................................. 19
LDO.............................................................................................. 20
Applications Information .............................................................. 21
Buck External Component Selection....................................... 21
LDO External Component Selection....................................... 23
Power Dissipation and Thermal Considerations ....................... 24
Buck Regulator Power Dissipation .......................................... 24
Junction Temperature ................................................................ 25
PCB Layout Guidelines.................................................................. 26
Typical Application Schematics.................................................... 27
Bill of Materials........................................................................... 27
Outline Dimensions ....................................................................... 28
Ordering Guide .......................................................................... 28
http://www.DataSheet4U.net/
Rev. A | Page 2 of 28
datasheet pdf - http://www.DataSheet4U.net/







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)