DatasheetsPDF.com

CNH20R105M-TM Dataheets PDF



Part Number CNH20R105M-TM
Manufacturers MARUWA
Logo MARUWA
Description High capacitance 3-terminal capacitors
Datasheet CNH20R105M-TM DatasheetCNH20R105M-TM Datasheet (PDF)

www.DataSheet4U.com PERFORMANCE AND TEST METHOD Item Performance CG, UJ R F Testing method and conditions (In accordance with JIS C5101-1) CG : 1MHz UJ, R, F : 1kHz Measurement voltage : 0.5~2Vrms Application time is 1~5seconds. CG, UJ : 300% of rated voltage R, F : 250% of rated voltage Rated voltage is applied for 1 minute. MARUWA GENERAL CATALOG Dissipation Factor 2.5% or less ‫ء‬1) 5% or less ‫ء‬1) Withstanding voltage No insulation breakdown and no failure. No less than 10,000M⍀ or 5.

  CNH20R105M-TM   CNH20R105M-TM


Document
www.DataSheet4U.com PERFORMANCE AND TEST METHOD Item Performance CG, UJ R F Testing method and conditions (In accordance with JIS C5101-1) CG : 1MHz UJ, R, F : 1kHz Measurement voltage : 0.5~2Vrms Application time is 1~5seconds. CG, UJ : 300% of rated voltage R, F : 250% of rated voltage Rated voltage is applied for 1 minute. MARUWA GENERAL CATALOG Dissipation Factor 2.5% or less ‫ء‬1) 5% or less ‫ء‬1) Withstanding voltage No insulation breakdown and no failure. No less than 10,000M⍀ or 500M⍀ • ␮F, whichever is smaller. Chip Insulation resistance Adhesion strength of termination 5N No peeling-off or exfoliation shall be manifest or recognizable in its incipient stages. No remarkable damage Within specified tolerance Initial standard values must be satisfied. No remarkable damage No more than ȗ2.5% or ȗ0.25pF, whichever is larger. Within ȗ7.5% Within ȗ20% Solder a specimen on the testing jig shown on the left and apply a force of 5N (0.51kgf) in the direction indicated by arrow. Substrate Visual Vibration resistance Capacitance Dissipation factor Visual Resistance to soldering heat Capacitance Dissipation factor Insulation resistance Withstanding voltage Vibration frequency : 10~55Hz Full amplitude : 1.5mm, 10~55~10Hz 1min. XYZ direction 2hrs for each total 6hrs. Solder Soldering temperature Immersion time Preheat : H60A or H63A (JIS Z 3282) : 270ȗ5°C : 10ȗ1sec. : 80~100°C (1~2min.) and 170~200°C (1~min.) Immersion into solder should be carried out continuously after preheating. Solder : H60A or H63 (JIS Z 3282A) Soldering temperature : 230ȗ5°C Immersion time : 2ȗ1sec. Step Temperature Time 1 Lower limit temp.‫ ء‬30min. 2 Room temp. 3min. 3 Upper limit temp.‫ ء‬30min. 4 Room temp. 3min. These four temperatures in the above order completes one cycle. The cycle is repeated 25 times. Initial standard values be satisfied. Initial standard values be satisfied. No damage or insulation breakdown. Solderability Termination surface should be covered with new solder to over 75%. Visual Capacitance Temperature cycling Dissipation factor Insulation resistance Withstanding voltage Visual Humidity load test Capacitance Dissipation factor Insulation resistance Visual Life test at high temperature load Capacitance Dissipation factor Insulation resistance No remarkable damage No more than ȗ2.5% or ȗ0.25pF, whichever is larger. Within ȗ7.5% Within ȗ20% Initial standard values must be satisfied. Initial standard values must be satisfied. No damage or insulation breakdown. No remarkable damage No more than ȗ5% or ȗ0.5pF, whichever is larger. Within ȗ12.5% EMI FILTERS Within ȗ30% Test temp : 40ȗ2°C Relative humidity : 90~95% Less than 7.5% ‫ء‬1) Testing time : 1000 +48, –0 100% of rated voltage is applied No less than 10,000M⍀ or 500M⍀ • ␮F, whichever is smaller. Less than 5% ‫ء‬1) No remarkable damage Within ȗ12.5% Test temp : Upper limit temp.ȗ3°C Within ȗ30% Testing time : 1000 +48, –0 Less than 7.5% ‫ء‬1) 200% of rated voltage is applied.‫ء‬2) Unit : mm Add load at a speed of 10 about 1mm per second 20 until flexion amount reaches 1mm and keep the condition R=230 for 5 minutes. Have a capacitance meter connected to both ends of sample during a test. 45±2 45±2 No more than ȗ3% or ȗ0.3pF, whichever is larger Less than 4% ‫ء‬1) No less than 10,000M⍀ or 500M⍀ • ␮F, whichever is smaller. Visual Flexion No mechanical damage Capacitance No more than ȗ5% or ȗ0.5pF, whichever is larger. Within ȗ12.5% Within ȗ30% *1) Dielectric dissipation factor Type name CNH20R224M–ȞM CNH20R474M–ȞM CNH20R105M–ȞM CNH20R475M–ȞM CNH20R106M–ȞM CNH10R105M–ȞM Temperature characteristics Rated voltage 16V R 6.3V 9% max. 12.5% max. 12.5% max. Initial 5% max. Moistureproof load 7.5% max. High-temperature load 7% max. *2) The following products are applied voltage 150%. CNH20R224M– Ȟ M CNH20R474M– Ȟ M CNH20R105M– Ȟ M The following product is applied rated voltage CNH20R475M– Ȟ M CNH20R106M– Ȟ M CNH10R105M– Ȟ M 90 .


PWR-10A-24194-GY CNH20R105M-TM 2SC2104


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)