Document
Wireless TV Link
SLV3100
User Manual
Free Datasheet http://www.datasheet-pdf.com/
A
1
2
SLV3100 WIRELESS TVLINK TRANSMITTER
IR
Channel 1234
DC 9V
ON/OFF ON/OFF
7
6
5
4
3
B
8
9
SLV3100 WIRELESS TVLINK RECEIVER
Channel 1234
DC 9V
ON/OFF ON/OFF
13
12
11
10
E
14
15
15
Free Datasheet http://www.datasheet-pdf.com/
Contents
Page
EN
4
4
Overview
Control and display elements
Your Wireless TV Link Safety Installation Operation
Enjoy your Wireless TV Link
5 5 6 8
8
Troubleshooting Information
Health and safety Maintenance and service Recycling and disposal Warranty Glossary
9 11
11 11 11 12 12
3
Free Datasheet http://www.datasheet-pdf.com/
EN
Overview
Control and display elements
A Transmitter
1 Power light: > green: on 2 Remote control signal light 3 On/off switch 4 Power input connector (DC 9V) 5 SCART cable 6 Wireless channel selection switch 7 Remote control blaster cord port
B Receiver
8 Power light: > green: on 9 Remote control signal light 10 On/off switch 11 Power input connector (DC 9V) 12 SCART cable 13 Wireless channel selection switch
E Remote control blaster cord
14 Connector 15 Blaster light
4
Free Datasheet http://www.datasheet-pdf.com/
Your Wireless TV Link
You can say good-bye to wires. With your Wireless TV Link you can now wirelessly connect a second TV and watch the device on your second TV.
EN
Safety
• • • • • • • • •
Read the instructions in this manual carefully before you connect, install and use the product. Keep this manual for future reference. The product is for indoor use only. Do not use the product close to water. Do not expose the product to extreme heat. In case of technical difficulties, do not open the product. Bring it to your Philips dealer. Do not cover the product. Connect the power adapters only to a 220-240 V AC/50 Hz power supply. The product can cause interference to other equipment. Check if any equipment near the product can be affected before you start using it.
5
Free Datasheet http://www.datasheet-pdf.com/
EN
Installation
For basic installation, see the quick start guide that came with your Wireless TV Link.
3
Enjoy
Install the remote control blaster cord
DC 9V ON/OFF
1 Switch off the transmitter (A).
1234
2 Connect the remote control blaster cord (E) to the IR socket. 3 Position the blaster light in front of the video source. See the user manual of the video source for the exact location of the IR sensor on the front panel.
DC 9V ON/OFF
4 5 6 7
Switch on the transmitter (A). Take the remote control of a video source with you. Go to TV2. Switch on TV2.
DC 9V ON/OFF
8 Switch on the receiver (B). 9 Select the correct SCART input on TV2. 10 Operate the video source with its remote control.
6
Free Datasheet http://www.datasheet-pdf.com/
Installation
Remove interference on TV2
1234
EN
1 Find the CHANNEL switch on the transmitter (A). 2 Set the CHANNEL switch to a different number.
1234
3 Find the CHANNEL switch on the receiver (B). 4 Set the CHANNEL switch to the same number as on the transmitter (A).
7
Free Datasheet http://www.datasheet-pdf.com/
EN
Operation
Enjoy your Wireless TV Link
For basic operation, see the quick start guide that came with your Wireless TV Link.
3
Enjoy
Watch a cable TV program on TV2
Your VCR or DVD recorder needs to be connected to the transmitter (A) of the Wireless TV Link and connected to the Cable-TV signal.
DC 9V ON/OFF
1 Switch on the transmitter (A). 2 Switch on the VCR or DVD recorder. 3 Take the remote control of the VCR or DVD recorder with you. 4 Go to TV2. 5 Switch on TV2. 6 Switch on the receiver (B). 7 Select the channel on the VCR or DVD recorder with its remote control. Turn off the auto standby mode when you use the VCR or DVD recorder to watch a cable tv program. Refer to the user manual of the VCR or DVD recorder.
DC 9V ON/OFF
If the VCR or DVD recorder records a television program, you watch the recorded channel.
Watch a video source on TV1
Operate TV1 and the video source as usual.
8
Free Datasheet http://www.datasheet-pdf.com/
Troubleshooting
Problem No image or wrong image on TV1 Tip • Make sure video source is connected to the transmitter (A). • Make sure the transmitter (A) is connected to TV1. • Make sure SCART cables are firmly inserted. • Make sure the video source is switched on. • Make sure the correct SCART input on TV1 is selected. • Make sure SCART cables are firmly inserted. • Make sure the receiver (B) is connected to TV2. • Make sure both receiver (B) and transmitter (A) are switched on. • Make sure the video source is switched on. • Make sure the correct SCART input on TV2 is selected. • If the video source gives proper image on TV1: Make sure the video source gives video signal in CVBS mode. See its user manual • Change the wireless channel that is used for communication. See page 7. • The receiver (B) is out of range of the transmitter (A). The number of walls and ceilings in between the receiver (B) and transmitter (A) restrict th.