Document
HI-8105 & HI-8106
January 2001
DESCRIPTION
The HI-8105 & HI-8106 are silicon gate CMOS devices designed for 'glue' logic applications. They are simple 16 stage dividers with programmable division. The HI-8105 has a one pin oscillator while the HI-8106 receives a clock input. The one pin oscillator frequency is set by a resistor to VDD and the capacitance to AC ground at the pin. The wafer processing enables operation to 1 volt guaranteed. The chip is designed for low power performance. As a result the maximum output frequency is 5 MHz while the internal logic will run considerably higher. A companion version, HI-8107, features a crystal oscillator circuit and a 8 stage programmable divider.
PIN CONFIGURATION
VDD 1 VSS 2 OUT 3 A0 4
8
on HI-8105 { OSC CLK on HI-8106
7 A3 6 A2 5 A1
SUPPLY VOLTAGES
VDD = 1V to 5V
FUNCTION TABLE
A3 A2 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 A1 A0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 OUT DIV by 2 4 8 16 32 64 128 256 512 1024 2048 4096 8192 16384 32768 65536
FEATURES
PIN DESCRIPTION TABLE
PIN 1 2 3 4 5 6 7 8 8 SYMBOL VDD VSS OUT A0 A1 A2 A3 OSC (8105) CLK (8106) FUNCTION SUPPLY SUPPLY LOGIC OUTPUT LOGIC INPUT LOGIC INPUT LOGIC INPUT LOGIC INPUT INPUT/OUTPUT LOGIC INPUT DESCRIPTION POSITIVE SUPPLY, 1V TO 5V GROUND CMOS CMOS CMOS CMOS CMOS RC - CONNECT TO VDD CMOS
(DS8105 Rev. A)
HOLT INTEGRATED CIRCUITS 1
01/01
HI-8105 & HI-8106
FUNCTIONAL DESCRIPTION
The HI8105 and HI-8106 are 16 stage serial counters. Each stage's Q is input to a 1 of 16 decoder. A 4 bit code at pins 4 through 7 selects which stage is routed to the output at pin 3. The counter clocks on the negative transition of pin 8. Figure 1 shows the oscillator circuit of the HI-8105. The charging time is controlled by a delay circuit and the hystersis window. The window is typically 0.6V wide at VDD=5.0V. Figure 2 shows the bonding option which omits the N device pulldown and thereby allows the simple clock input of the HI-8106.
VDD C o pin 8 R o clock
delay
FIGURE 1 - HI-8105 Oscillator
APPLICATION INFORMATION
The HI-8105 oscillator frequency is set by selecting a resistor and capacitor to apply at pin 8. Typical parameters at room temperature are: OSCILLATOR FREQUENCY DATA
Co = 100pF Ro 1KΩ 3KΩ 10KΩ 100KΩ VDD=5V 7.80MHz 4.22MHz 1.46MHz 165KHz VDD=1V 914KHz 464KHz 64KHz Co = 1nF VDD=5V 2.12MHz 1.10MHz 359KHz 39.6KHz VDD=1V 231KHz 100KHz 12KHz
pin 8
clock
FIGURE 2 - HI-8106 Clock Input
ORDERING INFORMATION
PART PACKAGE TEMPERATURE BURN LEAD
NUMBER HI-8105PDI HI-8105PDT HI-8105PSI HI-8105PST HI-8105CDI HI-8105CDT HI-8105CDM HI-8105CRI HI-8105CRT HI-8105CRM
DESCRIPTION 8 PIN PLASTIC DIP 8 PIN PLASTIC DIP 8 PIN PLASTIC NARROW BODY SOIC 8 PIN PLASTIC NARROW BODY SOIC 8 PIN CERAMIC SIDE BRAZED DIP 8 PIN CERAMIC SIDE BRAZED DIP 8 PIN CERAMIC SIDE BRAZED DIP 8 PIN CERDIP 8 PIN CERDIP 8 PIN CERDIP
RANGE -40°C TO +85°C -55°C TO +125°C -40°C TO +85°C -55°C TO +125°C -40°C TO +85°C -55°C TO +125°C -55°C TO +125°C -40°C TO +85°C -55°C TO +125°C -55°C TO +125°C
FLOW I T I T I T M I T M
IN NO NO NO NO NO NO YES NO NO YES
FINISH SOLDER SOLDER SOLDER SOLDER GOLD GOLD SOLDER SOLDER SOLDER SOLDER
Note: The HI-8106 is available in the same options
HOLT INTEGRATED CIRCUITS 2
HI-8105 & HI-8106 ABSOLUTE MAXIMUM RATINGS
Voltages referenced to Ground Supply voltages VCC...................................................7V DC current per input pin................ ±10mA Power dissipation at 25°C................500mW Solder Temperature ........275°C for 10 sec Storage Temperature........-65°C to +150°C NOTE: Stresses above absolute maximum ratings or outside recommended operating conditions may cause permanent damage to the device. These are stress ratings only. Operation at the limits is not recommended. Supply Voltages VCC........................................1V to 5.25V Temperature Range Industrial Screening........-40°C to +85°C Hi-Temp Screening.......-55°C to +125°C Military Screening.........-55°C to +125°C
RECOMMENDED OPERATING CONDITIONS
1.0 pins 4,5,6,7 3.5 2.5 2.5
5.0
1.5
pins 4,5,6,7 -1.0 1.0 pins 3 Vout=3.5V Vout=0.8V pins 4,5,6,7 all at VSS and pin 8 = VSS Ro=1KΩ and Co=100pF clocking pin 8 at 10MHz pins 4,5,6,7 all at VSS and Ro=10KΩ and Co=100pF 0.5 0.6 38 1.0 0.8 1.0 70
1.7
-2.4 2.8
-1.6
HOLT INTEGRATED CIRCUITS 3
HI-8105 / HI-8106 PACKAGE DIMENSIONS
inches (millimeters)
8-PIN PLASTIC DIP
Package Type: 8P
.385 ± .015 (4.699 ± .381)
.250 ± .010 (6.350 ± .254) .100 ± .010 (3.540 ± .254) .300 ± .010 (7.620 ± .254) .025 ± .010 (.635 ± .254) .0115 ± .0035 (.292 ± .089) .055 ± .010 (1.397 ± .254) .335 ± .035 (8.509 ± .889)
7° TYP. .135 ± .015 (3.429 ± .381) .1375 ± .0125 (3.493 ± .318) .019 ± .002 (.483 ± .102)
8-PIN PLASTIC SMALL OUTLINE (SOIC) - NB (Narrow Body)
.1935 ± .0035 (4.915 ± .085)
Package Type: 8HN
.0086 ± .0012 (.2184 ± .0305) .236 ± .008 (5.994 ± .203)
PIN 1
.1535 ± .0035 (3.90 ± .09)
.0165 ± .0035 (.4191 ± .0889)
Detail A.