DatasheetsPDF.com

1FT7064 Dataheets PDF



Part Number 1FT7064
Manufacturers Siemens
Logo Siemens
Description synchronous motors
Datasheet 1FT7064 Datasheet1FT7064 Datasheet (PDF)

SINAMICS S120 Drive Technology 1FT7 Synchronous Motors Configuring Manual Edition 04/2007 1FT7 synchronous motors SINAMICS S120 sinamics s Free Datasheet http://www.Datasheet4U.com Free Datasheet http://www.Datasheet4U.com Preface Motor description 1 2 3 4 5 6 7 8 A SINAMICS S120 1FT7 Synchronous Motors Use Mechanical data Electrical data Engineering software Motor components Technical data and characteristic curves Dimension drawings Appendix Configuration Manual (PFT7S), 04/2007 6SN1.

  1FT7064   1FT7064


Document
SINAMICS S120 Drive Technology 1FT7 Synchronous Motors Configuring Manual Edition 04/2007 1FT7 synchronous motors SINAMICS S120 sinamics s Free Datasheet http://www.Datasheet4U.com Free Datasheet http://www.Datasheet4U.com Preface Motor description 1 2 3 4 5 6 7 8 A SINAMICS S120 1FT7 Synchronous Motors Use Mechanical data Electrical data Engineering software Motor components Technical data and characteristic curves Dimension drawings Appendix Configuration Manual (PFT7S), 04/2007 6SN1197-0AD13-0BP0 Free Datasheet http://www.Datasheet4U.com Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. Danger indicates that death or severe personal injury will result if proper precautions are not taken. Warning indicates that death or severe personal injury may result if proper precautions are not taken. Caution with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. Caution without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. Notice indicates that an unintended result or situation can occur if the corresponding information is not taken into account. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The device/system may only be set up and used in conjunction with this documentation. Commissioning and operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes in this documentation qualified persons are defined as persons who are authorized to commission, ground and label devices, systems and circuits in accordance with established safety practices and standards. Prescribed Usage Note the following: Warning This device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and maintenance. Trademarks All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Automation and Drives Postfach 48 48 90437 NÜRNBERG GERMANY 6SN1197-0AD13-0BP0 Ⓟ 04/2007 Copyright © Siemens AG 2007. Technical data subject to change Free Datasheet http://www.Datasheet4U.com Preface Information on the documentation You will find an overview of the documentation, which is updated on a monthly basis, in the available languages on the Internet under: http://www.siemens.com/motioncontrol Select the menu items "Support" → "Technical Documentation" → "Overview of Publications". The Internet version of DOConCD (DOConWEB) is available at: http://www.automation.siemens.com/doconweb Information on the range of training courses and FAQs (frequently asked questions) are available on the Internet under: http://www.siemens.com/motioncontrol under menu option "Support" Target group Planners and project engineers Benefits The Configuration Manual supports you when selecting motors, calculating the drive components, selecting the required accessories as well as when selecting line and motorside power options. Standard scope The scope of the functionality described in this document can differ from the scope of the functionality of the drive system that is actually supplied. Other functions not described in this documentation might be able to be executed in the drive system. This does not, however, represent an obligation to supply such functions with a new control or when servicing. Extensions or changes made by the machine manufacturer are documented by the machine manufacturer. For the sake of simplicity, this documentation does not contain all detailed information about all types of the product and cannot cover every conceivable case of installation, operation, or maintenance. 1FT7 Synchronous Motors Configuration M.


1FT7062 1FT7064 1FT7082


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)