DatasheetsPDF.com

NCP4413 Dataheets PDF



Part Number NCP4413
Manufacturers ON Semiconductor
Logo ON Semiconductor
Description 3A High-Speed MOSFET Drivers
Datasheet NCP4413 DatasheetNCP4413 Datasheet (PDF)

NCP4413, NCP4414 3 A High-Speed MOSFET Drivers The NCP4413/4414 are 3 A CMOS buffer/drivers. They will not latch up under any conditions within their power and voltage ratings. They are not subject to damage when up to 5 V of noise spiking of either polarity that occurs on the ground pin. They can accept, without damage or logic upset, up to 500 mA of current of either polarity being forced back into their output. All terminals are fully protected against up to 4 kV of electrostatic discharge. A.

  NCP4413   NCP4413



Document
NCP4413, NCP4414 3 A High-Speed MOSFET Drivers The NCP4413/4414 are 3 A CMOS buffer/drivers. They will not latch up under any conditions within their power and voltage ratings. They are not subject to damage when up to 5 V of noise spiking of either polarity that occurs on the ground pin. They can accept, without damage or logic upset, up to 500 mA of current of either polarity being forced back into their output. All terminals are fully protected against up to 4 kV of electrostatic discharge. As MOSFET drivers, the NCP4413/4414 can easily switch 1800 pF gate capacitance in 20 nsec with matched rise and fall times, and provide low enough impedance in both the ON and the OFF states to ensure the MOSFET’s intended state will not be affected, even by large transients. The rise and fall time edges are matched to allow driving short–duration inputs with greater output accuracy. Features http://onsemi.com MARKING DIAGRAM 8 8 1 SO–8 D SUFFIX CASE 751 1 NCP 441x YWWXZ 8 PDIP–8 P SUFFIX CASE 626 1 x YY, Y WW, W X Z CO = Device Number (3 or 4) = Year = Work Week = Assembly ID Code = Subcontractor ID Code = Country of Origin NCP441x YYWWXZ CO • • • • • • • • • • • Latch–up Protected: Will Withstand 500 mA Reverse Current Input Will Withstand Negative Inputs Up to 5 V ESD Protected (4 kV) High Peak Output Current (3 A) Wide Operating Range (4.5 V to 16 V) High Capacitive Load Drive Capability (1800 pF in 20 nsec) Short Delay Time (35 nsec Typ) Consistent Delay Times with Changes in Supply Voltage Matched Delay Times Low Supply Current With Logic “1” Input (500 mA) With Logic “0” Input (100 mA) Low Output Impedance (2.7 W) 8 1 ORDERING INFORMATION Device NCP4413DR2 Inverting NCP4413P Inverting Package SO–8 PDIP–8 SO–8 PDIP–8 Shipping 2500 Tape & Reel 50 Units/Rail 2500 Tape & Reel 50 Units/Rail Functional Block Diagram NCP4413 INVERTING OUTPUTS VDD NCP4414DR2 Non–Inverting NCP4414P Non–Inverting 300 mV OUTPUT NONINVERTING OUTPUTS INPUT 4.7 V GND EFFECTIVE INPUT C = 10 pF NCP4414 © Semiconductor Components Industries, LLC, 2002 1 August, 2002 – Rev. 1 Publication Order Number: NCP4413/D http://www.Datasheet4U.com NCP4413, NCP4414 PIN CONNECTIONS 8–Pin SOIC/PDIP–8 VDD IN NC GND 1 2 3 4 8 8–Pin SOIC/PDIP–8 VDD 2 6, 7 IN NC INVERTING GND 1 2 3 4 8 VDD OUT OUT GND VDD OUT OUT GND NONINVERTING 2 6, 7 NCP4413 7 6 5 NCP4414 7 6 5 (Top View) NC = NO INTERNAL CONNECTION (Top View) http://onsemi.com 2 http://www.Datasheet4U.com NCP4413, NCP4414 ABSOLUTE MAXIMUM RATINGS* Rating Supply Voltage Input Voltage, IN A or IN B Maximum Chip Temperature Storage Temperature Range Lead Temperature (Soldering, 10 sec) Package Thermal Resistance SOIC SOIC Operating Temperature Range Power Dissipation (TA v 70°C) SOIC Tstg TSOI RθJA RθJC TA PD Symbol VDD VIN Value +20 VDD + 0.3 to GND – 5.0 +150 –65 to +150 +300 155 45 –40 to +85 470 °C mW Unit V V °C °C °C °C/W *Static–sensitive device. Unused devices must be stored in conductive material. Protect devices from static discharge and static fields. Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation section of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (Over operating temperature range with 4.5 V v VDD v 16 V, unless otherwise specified. Typical values are measured at TA = 25°C; VDD = 16 V.) Test Conditions Characteristic Input Logic 1 High Input Voltage Logic 0 Low Input Voltage Input Current Output High Output Voltage Low Output Voltage Output Resistance Peak Output Current Latch–Up Protection Withstand Reverse Current Switching Time (Note 1) Rise Time Fall Time Delay Time Delay Time Power Supply Power Supply Current IS VIN = 3 V VIN = 0 V VDD = 16 V – – 0.5 0.1 1.0 0.15 mA tR tF tD1 tD2 Figure 1 Figure 1 Figure 1 Figure 1 TA = 25°C – 40°C v TA v 85°C TA = 25°C – 40°C v TA v 85°C TA = 25°C – 40°C v TA v 85°C TA = 25°C – 40°C v TA v 85°C – – – – – – – – 20 24 20 24 35 40 35 40 28 33 28 33 45 50 45 50 nsec nsec nsec nsec VOH VOL RO IPK IREV DC Test DC Test VDD = 16 V, IO = 10 mA VDD = 16 V Duty Cycle v 2% t v 300 msec VDD = 16 V TA = 25°C – 40°C v TA v 85°C VDD – 0.025 – – – – 0.5 – – 2.7 3.3 3.0 – – 0.025 4.0 5.0 – – V v W A A VIH VIL IIN 0V v VIN v VDD – – TA = 25°C – 40°C v TA v 85°C 2.0 – –1.0 –10 – – – – – 0.8 1.0 10 V V mA Symbol Min Typ Max Unit 1. Switching times are guaranteed by design. http://onsemi.com 3 http://www.Datasheet4U.com NCP4413, NCP4414 +5 V INPUT VDD = 16 V 0V 4.7 µF 1, 8 INPUT 2 6, 7 OUTPUT CL = 1800 pF NCP4413 NCP4414 +5 V INPUT 4, 5 0V V DD INPUT: 100 kHz, square wave, tRISE = tFALL≤10 nsec OUTPUT 0V tD1 10% 10% 90% tR 0.1 µF V DD OUTPUT 0V 10% Inverting Driver NCP4413 10% tD1 90% tF 90% tD2 tR 90% 10% 90% 90% tD2 10% tF Noninver.


DMG4413LSS NCP4413 NCP4414


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)