Document
OS-CON DATA SHEET
OS-CON 20SVP150M
Frequency (kHz) Impedance (ohm) ESR (ohm) 0.12 8.650 0.089 0.5 2.159 0.040 1 1.050 0.030 10 0.110 0.019 100 0.016 0.012 500 0.018 0.010 1000 0.036 0.010 5000 0.167 0.011 10000 0.305 0.011
No.OS02N-DFSVP055
Frequency characteristics
1000
100
Impedance (ohm) ESR (ohm)
ESR, Impedance (ohm)
10
1
0.1
0.01
0.001 0.1 1 10 100 1000 10000
Frequency (kHz)
Measureing equipment: HP4194A Test fixture: HP16047C Measuring position: root of leads
OS Engineering Department, OS-CON Control Department Saga SANYO Industries Co., Ltd.
n = 3p.(Ave.) Room temperature
OS-CON DATA SHEET
SVP series Test item Endurance (After V.P.S test) Test temperature 105 deg.C Applied voltage 20 V Model 20SVP150M Lot No. 041205221
Change in capacitance (120Hz)
20 10 0.15 0.14 0.13 0.12 0.11 0.1 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0
Tangent of loss angle (120Hz)
0 -10 -20 -30 -40
0
2000
Tangent of loss angle
Percent delta [%]
0
2000
Time[h]
Time[h]
ESR (100kHz)
100 90 80 70 60 50 40 30 20 10 0 10000
Leakage current (20V 60s)
Leakage current(µA)
1000 100 10 1 0.1 0.01
ESR(mohm)
0
2000
0
2000
Time[h]
Time[h]
Note:
n =30p.
(V.P.S = Vapor Phase Soldering method)
Note: V.P.S test conditions : 230deg.C×75s×2times
Start on April 20, 2000 Executed by M. Koyama End on July 13, 2000 Drawn by M. Kimura No.OS02D-DESVP055 OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.
OS-CON DATA SHEET
SVP series Test item Damp heat (Steady state) (After V.P.S test) Test temperature 60 deg.C Test humidity 90 % RH Model 20SVP150M Lot No. 080102311
Change in capacitance (120Hz)
20 10 0.15 0.14 0.13 0.12 0.11 0.1 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0
Tangent of loss angle (120Hz)
Tangent of loss angle
Percent delta [%]
0 -10 -20 -30 -40
0
1000
0
1000
Time[h]
Time[h]
ESR (100kHz)
200 180 160 140 120 100 80 60 40 20 0 10000
Leakage current (20V 60s)
Leakage current(µA) 0 1000
1000 100 10 1 0.1 0.01
ESR(mohm)
0
1000
Time[h]
Time[h]
Note:
n =20p.
(V.P.S = Vapor Phase Soldering method)
Note: V.P.S test conditions : 230deg.C×75s×2times
Start on October 22, 2000 Executed by M. Koyama End on December 3, 2000 Drawn by M. Kimura No.OS02D-DHSVP055 OS Engineering Department, OS-CON Control Department, Saga SANYO Industries Co., Ltd.
.