DatasheetsPDF.com

PWM Controller. ISL6366 Datasheet

DatasheetsPDF.com

PWM Controller. ISL6366 Datasheet






ISL6366 Controller. Datasheet pdf. Equivalent




ISL6366 Controller. Datasheet pdf. Equivalent





Part

ISL6366

Description

Dual 6-Phase + 1-Phase PWM Controller

Manufacture

Intersil Corporation

Datasheet
Download ISL6366 Datasheet


Intersil Corporation ISL6366

ISL6366; Dual 6-Phase + 1-Phase PWM Controller fo r VR12/IMVP7 Applications ISL6366 The I SL6366 is a dual PWM controller; its 6- phase PWMs control the microprocessor c ore or memory voltage regulator, while its single-phase PWM controls the perip heral voltage regulator for graphics, s ystem agent, or processor I/O. The ISL6 366 utilizes Intersil’s proprietary E nhanced Active Pulse.


Intersil Corporation ISL6366

Positioning (EAPP) modulation scheme to achieve the extremely fast transient r esponse with fewer output capacitors. T he ISL6366 is designed to be compliant to Intel VR12/IMVP7 specifications. It accurately monitors the load current vi a the IMON pin and reports this informa tion via the IOUT register to the micro processor, which sends a PSI# signal to the controller at.


Intersil Corporation ISL6366

low power mode via SVID bus. The contro ller enters 1- or 2-phase operation in low power mode (PSI1); in the ultra low power mode (PSI2,3), it can further dr op the number of phases and enable the diode emulation ofthe operational phase .In low power modes, the magnetic core and switching losses are significantly reduced, yielding high efficiency at li ght load. After th.



Part

ISL6366

Description

Dual 6-Phase + 1-Phase PWM Controller

Manufacture

Intersil Corporation

Datasheet
Download ISL6366 Datasheet




 ISL6366
Dual 6-Phase + 1-Phase PWM Controller for VR12/IMVP7
Applications
ISL6366
The ISL6366 is a dual PWM controller; its 6-phase PWMs control
the microprocessor core or memory voltage regulator, while its
single-phase PWM controls the peripheral voltage regulator for
graphics, system agent, or processor I/O.
The ISL6366 utilizes Intersil’s proprietary Enhanced Active Pulse
Positioning (EAPP) modulation scheme to achieve the extremely
fast transient response with fewer output capacitors.
The ISL6366 is designed to be compliant to Intel VR12/IMVP7
specifications. It accurately monitors the load current via the
IMON pin and reports this information via the IOUT register to
the microprocessor, which sends a PSI# signal to the controller
at low power mode via SVID bus. The controller enters 1- or
2-phase operation in low power mode (PSI1); in the ultra low
power mode (PSI2,3), it can further drop the number of phases
and enable the diode emulation ofthe operational phase.In low
power modes, the magnetic core and switching losses are
significantly reduced, yielding high efficiency at light load. After
the PSI# signal is de-asserted, the dropped phase(s) are added
back to sustain heavy load transient response and efficiency.
Today’s microprocessors require a tightly regulated output voltage
position versus load current (droop). The ISL6366 senses the
output current continuously by measuring thevoltage acrossthe
dedicated current sense resistor or the DCRof the output
inductor. The sensed current flows outof the FB pinto develop the
precision voltage drop across the feedback resistor for droop
control. Currentsensing circuitsalso provide the needed signals
for channel-currentbalancing, average overcurrent protection and
individual phase current limiting. TheTM and TMS pins are to
sense anNTC thermistor’s temperature, which is internally
digitizedfor thermal monitoring and for integrated thermal
compensation of the current sense elements of therespective
regulator.
The ISL6366 features remote voltage sensing and completely
eliminates any potential difference between remote and local
grounds. This improves regulation and protection accuracy. The
threshold-sensitive enable input is available to accurately
coordinate the start-up of the ISL6366 with other voltage rails.
Features
• Intel VR12/IMVP7 Compliant
- SerialVID with Programmable IMAX, TMAX, BOOT,
ADDRESS OFFSET Registers
• Intersil’s Proprietary Enhanced Active Pulse Positioning
(EAPP) Modulation Scheme, Patented
- Voltage Feed-forward and Ramp Adjustable Options
- High Frequency and PSI Compensation Options
- Variable Frequency Control During Load Transients to
Reduce Beat Frequency Oscillation
- Linear Control with Evenly Distributed PWM Pulses for
Better Phase Current Balance During Load Transients
•D ual Outputs
- Output 1 (VR0): 1 to 6-Phase, Coupled Inductor
Compatibility, for Core or Memory
- Output 2 (VR1): Single Phase for Graphics, System Agent,
or Processor I/O
- Differential Remote Voltage Sensing
- ±0.5% Closed-loop System Accuracy Over Load, Line and
Temperature
- Phase Doubler Compatibility (NOT Phase Dropping)
• Proprietary Active Phase Adding and Dropping with Diode
Emulation Scheme For Enhanced Light Load Efficiency
• Programmable Slew Rate of Fast Dynamic VID with
Dynamic VID Compensation (DVC) for VR0
• Dynamic VID Compensation (DVS) for VR1 at No Droop
• Droop and Diode Emulation Options
• Programmable 1 or 2-Phase Operation in PSI1/2/3 Mode
• Programmable Standard or Coupled-Inductor Operation
• Precision Resistor or DCR Differential Current Sensing
- Integrated Programmable Current Sense Resistors
- Integrated Thermal Compensation
- Accurate Load-Line (Droop) Programming
- Accurate Channel-Current Balancing
- Accurate Current Monitoring
• Average Overcurrent Protection and Channel Current Limit
With Internal Current Comparators
• Precision Overcurrent Protection on IMON & IMONS Pins
• Independent Oscillators, up to 1MHz Per Phase, for Cost,
Efficiency, and Performance Optimization
• Dual Thermal Monitoring and Thermal Compensation
• Start-up Into Pre-Charged Load
• Pb-Free (RoHS Compliant)
Janu ar y 3, 20 11
FN6964.0
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 |Copyright Intersil Americas Inc. 2011. All Rights Reserved
Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.
http://www.Datasheet4U.com





 ISL6366
ISL6366
Ordering Information
PART NUMBER
(Note 1, 2, 3)
PART
MARKING
TEMP. RANGE
(°C)
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL6366CRZ
ISL6366 CRZ
0 to +70
60 Ld 7x7 QFN
L60.7x7
ISL6366IRZ
ISL6366 IRZ
-40 to +85
60 Ld 7x7 QFN
L60.7x7
NOTES:
1. Add “-T*” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte
tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Intersil Pb-
free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), please see device information page for ISL6366. For more information on MSL please see techbrief TB363.
Pin Configuration
ISL6366
(60 LD 7X7 QFN)
TOP VIEW
NC4 1
NC5 2
EN_PWR 3
RAMP_ADJ 4
RGND 5
VSEN 6
HFCOMP 7
PSICOMP 8
FB 9
COMP 10
DVC 11
IMON 12
SVDATA 13
SVALERT# 14
SVCLK 15
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46
45 PWM1
44 PWM4
43 PWM2
42 PWM5
41 VCC
40 FS_DRP
GND
39 RSET
38 SICI
37 TM
36 BTS_DES_TCOMPS
35 BT_FDVID_TCOMP
34 NPSI_DE_IMAX
33 ADDR_IMAXS_TMAX
32 PWMS
31 ISENS-
16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
2 FN6964.0
January 3, 2011





 ISL6366
ISL6366
Driver Recommendation
DRIVER
QUIESCENT
CURRENT (mA)
GATE
DRIVE
VOLTAGE
# OF DIODE EMULATION
DRIVERS
(DE)
GATE DRIVE
DROP
(GVOT)
COMMENTS
ISL6627
1.0
5V Single
Yes
No For PSI# channel and its coupled channel in
coupled inductor applications or all channels
ISL6620
1.2
5V Single
Yes
ISL6620A
No For PSI# channel and its coupled channel in
coupled inductor applications or all channels.
Shorter body diode conduction time when enters
PSI2 mode at a fixed voltage.
ISL6596
0.19
5V Single
No
No For dropped phases or all channels without DE
ISL6610
ISL6610A
0.24
5V Dual
No
No For dropped phases or all channels without DE
ISL6611A
1.25
5V Dual
No
No Phase Doubler with Integrated Drivers, up to 12-
Phase. For all channels with DE Disabled
ISL6617
5.0 N/A N/A No
No PWM Doubler for DrMOS, up to 12 or 24-Phase.
For all channels with DE Disabled
ISL6625
1.2
12V Single
Yes
Yes For PSI# channel and its coupled channel in
coupled inductor applications or all channels
ISL6622
5.5
12V Single
Yes
Yes For PSI# channel and its coupled channel in
coupled inductor applications or all channels.
Shorter body diode conduction time when enters
PSI2 mode at a fixed voltage.
ISL6622A
ISL6622B
5.5
12V Single
Yes
No For PSI# channel and its coupled channel in
coupled inductor applications or all channels.
Shorter body diode conduction time when enters
PSI2 mode at a fixed voltage.
ISL6625A
1.0
12V Single
No
No For dropped phases or all channels without DE
NOTE: Intersil 5V and 12V drivers are mostly pin-to-pin compatible and allow for dual footprint layout implementation to optimize MOSFET selection and
efficiency. 5V Drivers are more suitable for high frequency and high efficiency applications.
3 FN6964.0
January 3, 2011



Recommended third-party ISL6366 Datasheet






@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)