TA-SB500WR2 SERVICE MANUAL Datasheet

TA-SB500WR2 Datasheet, PDF, Equivalent


Part Number

TA-SB500WR2

Description

SURROUND AMPLIFIER SERVICE MANUAL

Manufacture

Sony

Total Page 30 Pages
Datasheet
Download TA-SB500WR2 Datasheet


TA-SB500WR2
TA-SB500WR2
SERVICE MANUAL
Ver. 1.0 2007.03
US Model
TA-SB500WR2 is the surround amplifier
section in DAV-HDX267W/HDX501W.
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 3 ohms loads, both
channels driven, from
120 Hz - 20,000 Hz; rated
60 watts per channel
minimum RMS power,
with no more than 0.7 %
total harmonic distortion
from 250 milli watts to
rated output.
Amplifier section
Surround mode (reference) RMS output power
SL/SR* : 100 W
(per channel at 3 ohms, 1
kHz, 10 % THD)
* Depending on the sound field setting and the source,
there may be no sound output.
Power requirements:
Power consumption
Dimensions (approx.)
Mass (approx.)
120 V AC, 60 Hz
On: 40 W
65 × 89 × 253 mm
(2 5/8 × 3 5/8 × 10 inches)
(w/h/d)
65 × 89 × 345 mm
(2 5/8 3 × 5/8 × 13 5/8 inches)
(w/h/d) incl. speaker cord
cover
1.3 kg (2 lb 14 oz)
1.4 kg (3 lb 2 oz) incl.
speaker cord cover
Design and specifications are subject to change
without notice.
9-887-591-01
2007C05-1
© 2007.03
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
SURROUND AMPLIFIER
http://www.Datasheet4U.com

TA-SB500WR2
TA-SB500WR2
Notes on chip component replacement
Never reuse a disconnected chip component.
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel a way if
the heated tip is applied for too long, so be careful!
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
TABLE OF CONTENTS
1. GENERAL ................................................................... 3
2. DISASSEMBLY
2-1. Disassembly Flow ........................................................... 4
2-2. Wire Cover ...................................................................... 4
2-3. Top Panel ......................................................................... 5
2-4. Side Panel, Front Panel Block ......................................... 5
2-5. DIAT POWER Board ...................................................... 6
2-6. DIAT AMP Board ............................................................ 6
3. DIAGRAMS
3-1. Block Diagram ................................................................ 7
3-2. Printed Wiring Board – DIAT AMP Section (1/2) – ....... 9
3-3. Printed Wiring Boards – DIAT AMP Section (2/2) – ...... 10
3-4. Schematic Diagram – DIAT AMP Section (1/4) – .......... 11
3-5. Schematic Diagram – DIAT AMP Section (2/4) – .......... 12
3-6. Schematic Diagram – DIAT AMP Section (3/4) – .......... 13
3-7. Schematic Diagram – DIAT AMP Section (4/4) – .......... 14
3-8. Printed Wiring Boards – POWER SUPPLY Section – .... 15
3-9. Schematic Diagram – POWER SUPPLY Section – ........ 16
4. EXPLODED VIEWS
4-1. Panel Section ................................................................... 23
4-2. DIAT AMP/DIAT POWER Boards Section .................... 24
5. ELECTRICAL PARTS LIST ................................ 25
SAFETY CHECK-OUT
After correcting the original service problem, perform the follwo ing
safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, scrwe s,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all e xposed metal par ts to an y exposed metal part ha ving a
return to chassis, must not e xceed 0.5 mA (500 microamper es.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the v oltage drop acr oss a r esistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanw a SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
0.15 µF
1.5 k
AC
voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE P ARTS LIST ARE CRITICAL TO SAFE OPERA TION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2


Features TA-SB500WR2 SERVICE MANUAL Ver. 1.0 2007 .03 US Model • TA-SB500WR2 is the s urround amplifier section in DAV-HDX267 W/HDX501W. SPECIFICATIONS AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL H ARMONIC DISTORTION: With 3 ohms loads, both channels driven, from 120 Hz - 20, 000 Hz; rated 60 watts per channel mini mum RMS power, with no more than 0.7 % total harmonic distortion from 250 mill i watts to rated output. Power requirem ents: Power consumption Dimensions (app rox.) 120 V AC, 60 Hz On: 40 W 65 × 89 × 253 mm (2 5/8 × 3 5/8 × 10 inches ) (w/h/d) 65 × 89 × 345 mm (2 5/8 3 5/8 × 13 5/8 inches) (w/h/d) incl. s peaker cord cover 1.3 kg (2 lb 14 oz) 1 .4 kg (3 lb 2 oz) incl. speaker cord co ver Mass (approx.) Amplifier section Surround mode (reference) RMS output po wer SL/SR* : 100 W (per channel at 3 oh ms, 1 kHz, 10 % THD) * Depending on the sound field setting and the source, th ere may be no sound output. Design and specifications are subject to change without notice. SURROUND AMPLIFIER.
Keywords TA-SB500WR2, datasheet, pdf, Sony, SURROUND, AMPLIFIER, SERVICE, MANUAL, A-SB500WR2, -SB500WR2, SB500WR2, TA-SB500WR, TA-SB500W, TA-SB500, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)