SERVICE MANUAL. RX-E100RSL Datasheet

RX-E100RSL MANUAL. Datasheet pdf. Equivalent

Part RX-E100RSL
Description AUDIO/VIDEO CONTROL RECEIVER SERVICE MANUAL
Feature RX-E100RSL/RX-E100RSB SERVICE MANUAL AUDIO/VIDEO CONTROL RECEIVER RX-E100RSL RX-E100RSB AUDIO DVD .
Manufacture JVC
Datasheet
Download RX-E100RSL Datasheet



RX-E100RSL
RX-E100RSL/RX-E100RSB
SERVICE MANUAL
AUDIO/VIDEO CONTROL RECEIVER
AUDIO
DVD STB VCR
TV
SLEEP TV DIRECT
DVD STB VCR
TV
ANALOG/DIGITAL
INPUT
TAPE
FM
AM
SOUND
BASS+
1
CENTER
23
TEST
BASS–
4
REAR-L
56
BASS BOOST TREBLE+
7
REAR-R
89
EFFECT
TREBLE–
10
RETURN
SUBWOOFER
0 +10
FM MODE
100+
DISPLAY MODE
EON SELECT
DVD MENU
PTY(
DSP
MODE
EON
ENTER
RDS
DVD
MENU
PTY9
SURROUND
ON/OFF
PTY SEARCH
TV VOL CHANNEL
VOLUME
TV/VIDEO
DIMMER
VCR MUTING
CONTROL
/REW
DOWN
REC
PLAY
TUNING
STOP
FF/
UP
PAUSE
RM-SRXE100R REMOTE CONTROL
HOME CINEMA CONTROL CENTER
RX-E100RSL
RX-E100RSB
Area Suffix
RX-E100RSL
B U.K.
E Continental Europe
EN Northern Europe
RX-E100RSB
E Continental Europe
EN Northern Europe
STANDBY
TV DILECT
SETTING ADJUST
CONTROL
MEMORY
DIGITAL
SURROUND D I G I T A L
RX-E100R HOME CINEMA CONTROL CENTER
DVD
STB
VCR
TV
TAPE
FM/AM
ANALOG L C R PRO LOGIC SLEEP
LPCM SUBWFR LFE DSP
DOLBY D
DGTL AUTO
DTS LS S RS INPUT ATT
TUNED ST AUTO MUTING
MHZ
KHZ
VOL
DVD
STB
VCR
TV
TAPE
FM/AM
INPUT SURROUND
ANALOG/DIGITAL ON/OFF
DSP
MODE
INPUT ATT
MASTER VOLUME
Each difference points
MODEL
Source indication lens colour
RX-E100RSL
SILVER
RX-E100RSB
SILVER BLACK
Contents
Safety precautions --------------------------------------------------------1- 2
Disassembly method -----------------------------------------------------1- 3
Adjustment method -------------------------------------------------------1- 8
Description of major ICs -------------------------------------------------1- 9
15
COPYRIGHT 2001 VICTOR COMPANY OF JAPAN, LTD.
No.20951
May 2001



RX-E100RSL
RX-E100RSL/RX-E100RSB
1. This design of this product contains special hardware and many circuits and components specially for safety
purposes. For continued protection, no changes should be made to the original design unless authorized in
writing by the manufacturer. Replacement parts must be identical to those used in the original circuits. Services
should be performed by qualified personnel only.
2. Alterations of the design or circuitry of the product should not be made. Any design alterations of the product
should not be made. Any design alterations or additions will void the manufacturer`s warranty and will further
relieve the manufacture of responsibility for personal injury or property damage resulting therefrom.
3. Many electrical and mechanical parts in the products have special safety-related characteristics. These
characteristics are often not evident from visual inspection nor can the protection afforded by them necessarily
be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts which
have these special safety characteristics are identified in the Parts List of Service Manual. Electrical
components having such features are identified by shading on the schematics and by ( ) on the Parts List in
the Service Manual. The use of a substitute replacement which does not have the same safety characteristics
as the recommended replacement parts shown in the Parts List of Service Manual may create shock, fire, or
other hazards.
4. The leads in the products are routed and dressed with ties, clamps, tubings, barriers and the like to be
separated from live parts, high temperature parts, moving parts and/or sharp edges for the prevention of
electric shock and fire hazard. When service is required, the original lead routing and dress should be
observed, and it should be confirmed that they have been returned to normal, after re-assembling.
5. Leakage currnet check (Electrical shock hazard testing)
After re-assembling the product, always perform an isolation check on the exposed metal parts of the product
(antenna terminals, knobs, metal cabinet, screw heads, headphone jack, control shafts, etc.) to be sure the
product is safe to operate without danger of electrical shock.
Do not use a line isolation transformer during this check.
Plug the AC line cord directly into the AC outlet. Using a "Leakage Current Tester", measure the leakage
current from each exposed metal parts of the cabinet, particularly any exposed metal part having a return
path to the chassis, to a known good earth ground. Any leakage current must not exceed 0.5mA AC (r.m.s.).
Alternate check method
Plug the AC line cord directly into the AC outlet. Use an AC voltmeter having, 1,000 ohms per volt or more
sensitivity in the following manner. Connect a 1,500 10W resistor paralleled by a 0.15 F AC-type capacitor
between an exposed metal part and a known good earth ground.
Measure the AC voltage across the resistor with the AC
AC VOLTMETER
(Having 1000
voltmeter.
Move the resistor connection to eachexposed metal part,
ohms/volts,
or more sensitivity)
particularly any exposed metal part having a return path to
the chassis, and meausre the AC voltage across the resistor.
Now, reverse the plug in the AC outlet and repeat each
measurement. voltage measured Any must not exceed 0.75 V
AC (r.m.s.). This corresponds to 0.5 mA AC (r.m.s.).
0.15 F AC TYPE
1500 10W
Place this
probe on
each exposed
metal part.
Good earth ground
1. This equipment has been designed and manufactured to meet international safety standards.
2. It is the legal responsibility of the repairer to ensure that these safety standards are maintained.
3. Repairs must be made in accordance with the relevant safety standards.
4. It is essential that safety critical components are replaced by approved parts.
5. If mains voltage selector is provided, check setting for local voltage.
!
Burrs formed during molding may
be left over on some parts of the
chassis. Therefore, pay attention to
such burrs in the case of
preforming repair of this system.
In regard with component parts appearing on the silk-screen printed side (parts side) of the PWB diagrams, the
parts that are printed over with black such as the resistor ( ), diode ( ) and ICP ( ) or identified by the " "
mark nearby are critical for safety.
When replacing them, be sure to use the parts of the same type and rating as specified by the manufacturer.
(Except the JC version)
1-2





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)