DatasheetsPDF.com

HAS50-P Dataheets PDF



Part Number HAS50-P
Manufacturers LEM
Logo LEM
Description Current Transducer
Datasheet HAS50-P DatasheetHAS50-P Datasheet (PDF)

Current Transducer HAS 50 ... 600-P For the electronic measurement of currents: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit. IP N = 50 ... 600 A Electrical data Type Primary nominal Primary current, RoHS since RMS current measuring range date code IP N (A) HAS 50-P 50 IP M (A) ±150 46065 HAS 100-P 100 ±300 46062 HAS 200-P 200 ±600 76273 HAS 300-P 300 ±900 76273 HAS 400-P 400 ±900 46131 HAS 500-P 500 ±900 46.

  HAS50-P   HAS50-P


Document
Current Transducer HAS 50 ... 600-P For the electronic measurement of currents: DC, AC, pulsed..., with galvanic separation between the primary circuit and the secondary circuit. IP N = 50 ... 600 A Electrical data Type Primary nominal Primary current, RoHS since RMS current measuring range date code IP N (A) HAS 50-P 50 IP M (A) ±150 46065 HAS 100-P 100 ±300 46062 HAS 200-P 200 ±600 76273 HAS 300-P 300 ±900 76273 HAS 400-P 400 ±900 46131 HAS 500-P 500 ±900 46216 HAS 600-P 600 ±900 76273 UC Supply voltage (±5 %) 1) ±15 V IC Current consumption ±15 mA RINS Insulation resistance @ 500 V DC > 1000 MΩ Uout Output voltage (Analog) @ ±IP N, RL = 10 kΩ, TA = 25 °C ±4 V Rout Output internal resistance approx 100 Ω RL Load resistance 10 kΩ Accuracy - Dynamic performance data Features ● Hall effect measuring principle ● Insulating plastic case made of polycarbonate PBT recognized according to UL 94-V0. Advantages ● Easy mounting ● Low power consumption ● Small size and space saving ● Only one design for wide current ratings range ● High immunity to external interference. εtot Total error @ IP N, TA = 25 °C (excluding offset) < ±1 % of IP N εL Linearity error 2) (0 ... ±IP N) < ±1 % of IP N UO E Electrical offset voltage, TA = 25 °C < ±20 mV UO H Hysteresis offset voltage @ IP = 0, after an excursion of 1 × IP N < ±20 mV TCUO E Temperature coefficient of UO E HAS 50-P < ±2 mV/K HAS 100 ... 600-P < ±1 mV/K TCUout Temperature coefficient of Uout (% of reading) tD 90 Delay time to 90 % of IP N 3) BW Frequency bandwidth 4) (small signal, −3 dB) < ±0.1 %/K < 3 µs DC ... 50 kHz General data Applications ● AC variable speed drives ● Static converters for DC motor drives ● Battery supplied applications ● Uninterruptible Power Supplies (UPS) ● Switched Mode Power Supplies (SMPS) ● Power supplies for welding applications. TA Ambient operating temperature TS Ambient storage temperature m Mass Standards UL −10 ... +80 °C −25 ... +85 °C 80 g UL 508:2010 5) Application domain ● Industrial. EMC IEC 61000-6-2:2016 IEC 61800-3:2017 6) Safety IEC 61010-1:2010 Environmental IEC 61477-1:2012 IEC 61800-2:2012 Notes: 1) Operating at ±12 V ≤ UC < ±15 V will reduce the measuring range 2) Linearity data exclude the electrical offset 3) For a di/dt = 50 A/µs 4) Under small signals condition 5) UL conform at +80 °C 6) Regarding compliance towards IEC 61000-4-3 (IEC 61800-3:2017): variation of the offset between 390 MHz and 400 MHz with a field intensity of 10 [V/m]. N° 74.72.25.000.0, N° 74.72.34.000.0, N° 74.72.44.000.0, N° 74.72.46.000.0, N° 74.72.48.000.0, N° 74.72.50.000.0, N° 74.72.52.000.0 Page 1/3 10March2020/version 10 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com Current Transducer HAS 50 ... 600-P Insulation coordination Ud RMS voltage for AC insulation test, 50 Hz/1 min 3.6 kV UNi Impulse withstand voltage 1.2/50 µs > 6.6 kV Min dCp Creepage distance dCI Clearance CTI Comparative tracking index (group IIIa) 7 mm 4.6 mm 275 Applications examples According to IEC 61010-1 standard and following conditions: ● Over voltage category OV 3 ● Pollution degree PD2 ● Non-uniform field dCp, dCI, UNi Basic insulation Reinforced insulation Safety IEC 61010-1 Nominal voltage 300 V 150 V This transducer must be used in limited-energy secondary circuits according to IEC 61010-1. This transducer must be used in electric/electronic equipment with respect to applicable standards and safety requirements in accordance with the manufacturer’s operating instructions. Caution, risk of electrical shock When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a build-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. 10March2020/version 10 LEM reserves the right to carry out modifications on its transducers, in order to improve them, without prior notice Page 2/3 LEM International SA Chemin des Aulx 8 1228 PLAN-LES-OUATES Switzerland www.lem.com Dimensions HAS 50 ... 600-P (in mm) dCl dCp Mechanical characteristics ● General tolerance ● Transducer fastening Recommended fastening torque ● Connection of secondary ±0.5 mm 1 hole ⌀ 4.5 mm 1 M4 steel screw 0.75 N·m (±10 %) JST MB4P-90H dCl dCp Connection IP UC RL UC IP RL.


HAS400-S HAS50-P HAS50-S


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)